lkml.org 
[lkml]   [2017]   [Oct]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH V8 00/14] mmc: Add Command Queue support
[...]

>>>>
>>>> I have also run some test on my ux500 board and enabling the blkmq
>>>> path via the new MMC Kconfig option. My idea was to run some iozone
>>>> comparisons between the legacy path and the new blkmq path, but I just
>>>> couldn't get to that point because of the following errors.
>>>>
>>>> I am using a Kingston 4GB SDHC card, which is detected and mounted
>>>> nicely. However, when I decide to do some writes to the card I get the
>>>> following errors.
>>>>
>>>> root@ME:/mnt/sdcard dd if=/dev/zero of=testfile bs=8192 count=5000 conv=fsync
>>>> [ 463.714294] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>>>> [ 464.722656] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>>>> [ 466.081481] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>>>> [ 467.111236] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>>>> [ 468.669647] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>>>> [ 469.685699] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>>>> [ 471.043334] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>>>> [ 472.052337] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>>>> [ 473.342651] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>>>> [ 474.323760] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>>>> [ 475.544769] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>>>> [ 476.539031] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>>>> [ 477.748474] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>>>> [ 478.724182] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>>>>
>>>> I haven't yet got the point of investigating this any further, and
>>>> unfortunate I have a busy schedule with traveling next week. I will do
>>>> my best to look into this as soon as I can.
>>>>
>>>> Perhaps you have some ideas?
>>>
>>> The behaviour depends on whether you have MMC_CAP_WAIT_WHILE_BUSY. Try
>>> changing that and see if it makes a difference.
>>
>> Yes, it does! I disabled MMC_CAP_WAIT_WHILE_BUSY (and its
>> corresponding code in mmci.c) and the errors goes away.
>>
>> When I use MMC_CAP_WAIT_WHILE_BUSY I get these problems:
>>
>> [ 223.820983] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>> [ 224.815795] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>> [ 226.034881] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>> [ 227.112884] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>> [ 227.220275] mmc0: Card stuck in wrong state! mmcblk0 mmc_blk_card_stuck
>> [ 228.686798] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>> [ 229.892150] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>> [ 231.031890] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>> [ 232.239013] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
>> 5000+0 records in
>> 5000+0 records out
>> root@ME:/mnt/sdcard
>>
>> I looked at the new blkmq code from patch v10 13/15. It seems like the
>> MMC_CAP_WAIT_WHILE_BUSY is used to determine whether the async request
>> mechanism should be used or not. Perhaps I didn't looked close enough,
>> but maybe you could elaborate on why this seems to be the case!?
>
> MMC_CAP_WAIT_WHILE_BUSY is necessary because it means that a data transfer
> request has finished when the host controller calls mmc_request_done(). i.e.
> polling the card is not necessary.

Well, that is a rather big change on its own. Earlier we polled with
CMD13 to verify that the card has moved back to the transfer state, in
case it was a write. And that was no matter of MMC_CAP_WAIT_WHILE_BUSY
was set or not. Right!?

I am not sure it's a good idea to bypass that validation, it seems
fragile to rely only on the busy detection on DAT line for writes.

>
> Have you tried V9 or V10. There was a fix in V9 related to calling
> ->post_req() which could mess up DMA.

I have used V10.

>
> The other thing that could go wrong with DMA is if it cannot accept
> ->post_req() being called from mmc_request_done().

I don't think mmci has a problem with that, however why do you want to
do this? Wouldn't that defeat some of the benefits with the async
request mechanism?

Kind regards
Uffe

\
 
 \ /
  Last update: 2017-10-10 15:08    [W:0.091 / U:1.316 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site