lkml.org 
[lkml]   [2017]   [Jan]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 17/22] power: supply: add battery driver for AXP20X and AXP22X PMICs
From
Date
Hi,

On 06/01/2017 04:39, Chen-Yu Tsai wrote:
> Hi,
>
> On Tue, Jan 3, 2017 at 12:37 AM, Quentin Schulz
> <quentin.schulz@free-electrons.com> wrote:
[...]
>> + case POWER_SUPPLY_PROP_CURRENT_MAX:
>> + ret = regmap_read(axp20x_batt->regmap, AXP20X_CHRG_CTRL1, &reg);
>> + if (ret)
>> + return ret;
>> +
>> + reg &= AXP20X_CHRG_CTRL1_TGT_CURR;
>> + val->intval = reg * 100000 + 300000;
>> + break;
>
>
> This controls the charge current. I believe the correct property to use
> is CONSTANT_CHARGE_CURRENT. And you should add CONSTANT_CHARGE_CURRENT_MAX
> which returns the highest possible setting.
>

ACK.

> Also letting the user control this might not always be a good idea.
> IIUC, LiPo batteries can only be charged at 1C, where C is the
> rated capacity (X mAh).
>

OK. Should I get the charge current from a DT property then?

Like "x-powers,charge-current = <300000>;"
It's close to what has been done in bq24257_charger for example.

[...]
>> +static enum power_supply_property axp20x_battery_props[] = {
>> + POWER_SUPPLY_PROP_PRESENT,
>> + POWER_SUPPLY_PROP_ONLINE,
>> + POWER_SUPPLY_PROP_STATUS,
>> + POWER_SUPPLY_PROP_VOLTAGE_NOW,
>> + POWER_SUPPLY_PROP_CURRENT_NOW,
>> + POWER_SUPPLY_PROP_CURRENT_MAX,
>> + POWER_SUPPLY_PROP_HEALTH,
>> + POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN,
>> + POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN,
>> + POWER_SUPPLY_PROP_CAPACITY,
>
> You can also add POWER_SUPPLY_PROP_TECHNOLOGY, which would return
> POWER_SUPPLY_TECHNOLOGY_LIPO.
>

Hum.. There are also POWER_SUPPLY_TECHNOLOGY_LION,
POWER_SUPPLY_TECHNOLOGY_LiFe and POWER_SUPPLY_TECHNOLOGY_LiMn which are
all Lithium-based batteries. From the datasheet, it can take a "single
cell Li-battery (Li-Ion/Polymer)". So I guess it's either
POWER_SUPPLY_TECHNOLOGY_LION or POWER_SUPPLY_TECHNOLOGY_LIPO.

> It is also possible to do POWER_SUPPLY_PROP_CHARGE_TYPE. According
> to the manual, if the battery is charging, it is in constant current
> mode (POWER_SUPPLY_CHARGE_TYPE_FAST) when V_battery < V_target.
> When V_battery == V_target, it is in constant voltage mode, though
> I don't think this is the same as POWER_SUPPLY_CHARGE_TYPE_TRICKLE.
> When it is not charging, you can return POWER_SUPPLY_CHARGE_TYPE_NONE.
>

ACK, I'll look into that.

Thanks,
Quentin

--
Quentin Schulz, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

\
 
 \ /
  Last update: 2017-01-06 14:13    [W:0.195 / U:0.556 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site