lkml.org 
[lkml]   [2017]   [Jan]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH 1/4] PCI: Xilinx NWL: Fix, do not check for legacy status in while loop
Date
> On 24/01/17 10:15, Bharat Kumar Gogada wrote:
> >> On 21/01/17 11:11, Bharat Kumar Gogada wrote:
> >>> - The legacy status register value for particular INTx becomes low
> >>> only after DEASSERT_INTx is received.
> >>> - Few End Points take time for sending DEASSERT_INTx, checking
> >>> legacy status register in while loop causes invoking of EP handler
> >>> continuosly until DEASSERT_INTx is received.
> >>>
> >>> Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
> >>> ---
> >>> drivers/pci/host/pcie-xilinx-nwl.c | 5 +++--
> >>> 1 files changed, 3 insertions(+), 2 deletions(-)
> >>>
> >>> diff --git a/drivers/pci/host/pcie-xilinx-nwl.c
> >>> b/drivers/pci/host/pcie-xilinx-nwl.c
> >>> index 43eaa4a..c8b5a33 100644
> >>> --- a/drivers/pci/host/pcie-xilinx-nwl.c
> >>> +++ b/drivers/pci/host/pcie-xilinx-nwl.c
> >>> @@ -342,9 +342,10 @@ static void nwl_pcie_leg_handler(struct
> >>> irq_desc
> >>> *desc)
> >>>
> >>> chained_irq_enter(chip, desc);
> >>> pcie = irq_desc_get_handler_data(desc);
> >>> + status = nwl_bridge_readl(pcie, MSGF_LEG_STATUS) &
> >>> + MSGF_LEG_SR_MASKALL;
> >>>
> >>> - while ((status = nwl_bridge_readl(pcie, MSGF_LEG_STATUS) &
> >>> - MSGF_LEG_SR_MASKALL) != 0) {
> >>> + if (status != 0) {
> >>> for_each_set_bit(bit, &status, INTX_NUM) {
> >>> virq = irq_find_mapping(pcie->legacy_irq_domain,
> >>> bit + 1);
> >>>
> >>
> >> But even if you only handle the interrupt once, it is still asserted,
> >> right? You exit the low-level exception handler, only to take the
> >> interrupt immediately again. So what is the gain here?
> >>
> > Whenever masking of INTx happens (like as in my next patch[PATCH
> > 2/4]), the irq line goes low, but status bit will be set until DEASSERT_INTx
> comes.
> > In this scenario if it is always in while loop, even though line went
> > low it will not be seen until DEASSERT_INTx, unnecessarily invoking EP
> > driver. so instead of while loop using if condition so that this change in line is
> noticed.
>
> But what guarantees that you will observe this DEASSERT if you return to the
> interrupted context early? From what I understand, your interrupt flow is the
> following:
>
>
> read status
> mask
> handler
> unmask
>
> If the EP takes time to send a deassert after the handler has poked it and the
> interrupt is still active, then the only thing that this patch buys you is that by
> returning to the interrupted context, you waste a lot of cycles, giving the device
> a chance to send its deassert. But that's just luck. Plug this on a fast CPU, and
> the same issue will resurface.
>

Agreed, will leave it as it is.

Thanks & Regards,
Bharat




\
 
 \ /
  Last update: 2017-01-24 15:01    [W:0.062 / U:0.324 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site