lkml.org 
[lkml]   [2017]   [Jan]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH net-next v3 06/10] net: dsa: Migrate to device_find_class()
From
Date
On 01/15/2017 11:16 AM, Andrew Lunn wrote:
>>> What exactly is the relationship between these devices (a ascii-art tree
>>> or sysfs tree output might be nice) so I can try to understand what is
>>> going on here.
>
> Hi Greg, Florian
>
> A few diagrams and trees which might help understand what is going on.
>
> The first diagram comes from the 2008 patch which added all this code:
>
> +-----------+ +-----------+
> | | RGMII | |
> | +-------+ +------ 1000baseT MDI ("WAN")
> | | | 6-port +------ 1000baseT MDI ("LAN1")
> | CPU | | ethernet +------ 1000baseT MDI ("LAN2")
> | |MIImgmt| switch +------ 1000baseT MDI ("LAN3")
> | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4")
> | | | |
> +-----------+ +-----------+
>
> We have an ethernet switch and a host CPU. The switch is connected to
> the CPU in two different ways. RGMII allows us to get Ethernet frames
> from the CPU into the switch. MIImgmt, is the management bus normally
> used for Ethernet PHYs, but Marvell switches also use it for Managing
> switches.
>
> The diagram above is the simplest setup. You can have multiple
> Ethernet switches, connected together via switch ports. Each switch
> has its own MIImgmt connect to the CPU, but there is only one RGMII
> link.
>
> When this code was designed back in 2008, it was decided to represent
> this is a platform device, and it has a platform_data, which i have
> slightly edited to keep it simple:
>
> struct dsa_platform_data {
> /*
> * Reference to a Linux network interface that connects
> * to the root switch chip of the tree.
> */
> struct device *netdev;
>
> /*
> * Info structs describing each of the switch chips
> * connected via this network interface.
> */
> int nr_chips;
> struct dsa_chip_data *chip;
> };
>
> This netdev is the CPU side of the RGMII interface.
>
> Each switch has a dsa_chip_data, again edited:
>
> struct dsa_chip_data {
> /*
> * How to access the switch configuration registers.
> */
> struct device *host_dev;
> int sw_addr;
> ...
> }
>
> The host_dev is the CPU side of the MIImgmt, and we have the address
> the switch is using on the bus.
>
> During probe of this platform device, we need to get from the
> struct device *netdev to a struct net_device *dev.
>
> So the code looks in the device net class to find the device
>
> | | | |-- f1074000.ethernet
> | | | | |-- deferred_probe
> | | | | |-- driver -> ../../../../../bus/platform/drivers/mvneta
> | | | | |-- driver_override
> | | | | |-- modalias
> | | | | |-- net
> | | | | | `-- eth1
> | | | | | |-- addr_assign_type
> | | | | | |-- address
> | | | | | |-- addr_len
> | | | | | |-- broadcast
> | | | | | |-- carrier
> | | | | | |-- carrier_changes
> | | | | | |-- deferred_probe
> | | | | | |-- device -> ../../../f1074000.ethernet
>
> and then use container_of() to get the net_device.
>
> Similarly, the code needs to get from struct device *host_dev to a struct mii_bus *.
>
> | | | |-- f1072004.mdio
> | | | | |-- deferred_probe
> | | | | |-- driver -> ../../../../../bus/platform/drivers/orion-mdio
> | | | | |-- driver_override
> | | | | |-- mdio_bus
> | | | | | `-- f1072004.mdio-mi
> | | | | | |-- deferred_probe
> | | | | | |-- device -> ../../../f1072004.mdio
>

Thanks Andrew! Greg, does that make it clearer how these devices
references are used, do you still think the way this is done is wrong,
too cautious, or valid?
--
Florian

\
 
 \ /
  Last update: 2017-01-16 21:01    [W:0.099 / U:1.084 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site