lkml.org 
[lkml]   [2017]   [Jan]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH 2/5 v3] drm/bridge: adv7511: Switch to using drm_kms_helper_hotplug_event()
Date
On Monday 16 Jan 2017 17:47:46 Laurent Pinchart wrote:
> Hi John,
>
> Thank you for the patch.
>
> On Tuesday 03 Jan 2017 11:41:39 John Stultz wrote:
> > In chasing down a previous issue with EDID probing from calling
> > drm_helper_hpd_irq_event() from irq context, Laurent noticed
> > that the DRM documentation suggests that
> > drm_kms_helper_hotplug_event() should be used instead.
> >
> > Thus this patch replaces drm_helper_hpd_irq_event() with
> > drm_kms_helper_hotplug_event(), which requires we update the
> > connector.status entry and only call _hotplug_event() when the
> > status changes.
> >
> > Cc: David Airlie <airlied@linux.ie>
> > Cc: Archit Taneja <architt@codeaurora.org>
> > Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
> > Cc: Lars-Peter Clausen <lars@metafoo.de>
> > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> > Cc: dri-devel@lists.freedesktop.org
> > Signed-off-by: John Stultz <john.stultz@linaro.org>
> > ---
> > v3: Update connector.status value and only call __hotplug_event()
> >
> > when that status changes, as suggested by Laurent.
> >
> > drivers/gpu/drm/bridge/adv7511/adv7511_drv.c | 16 +++++++++++++++-
> > 1 file changed, 15 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> > b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c index 4fcea44..d93d66f
> > 100644
> > --- a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> > +++ b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> > @@ -405,8 +405,22 @@ static bool adv7511_hpd(struct adv7511 *adv7511)
> >
> > static void adv7511_hpd_work(struct work_struct *work)
> > {
> >
> > struct adv7511 *adv7511 = container_of(work, struct adv7511,
>
> hpd_work);
>
> > + enum drm_connector_status status;
> > + unsigned int val;
> > + int ret;
> > +
> > + ret = regmap_read(adv7511->regmap, ADV7511_REG_STATUS, &val);
> > + if (ret < 0)
> > + status = connector_status_disconnected;
> > + else if (val & ADV7511_STATUS_HPD)
> > + status = connector_status_connected;
> > + else
> > + status = connector_status_disconnected;
> > +
> > + if (adv7511->connector.status != status)
> > + drm_kms_helper_hotplug_event(adv7511->connector.dev);
> >
> > - drm_helper_hpd_irq_event(adv7511->connector.dev);
> > + adv7511->connector.status = status;
>
> Shouldn't you update the status before calling
> drm_kms_helper_hotplug_event() ? Doing it after not only creates a small
> race condition as
> drm_kms_helper_hotplug_event() sends an event to userspace that could result
> in an ioctl call to retrieve the status, but the status is also checked by
> drm_setup_crtcs() called by drm_fb_helper_hotplug_event().

With

if (adv7511->connector.status != status) {
adv7511->connector.status = status;
drm_kms_helper_hotplug_event(adv7511->connector.dev);
}

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> > }
> >
> > static int adv7511_irq_process(struct adv7511 *adv7511, bool process_hpd)

--
Regards,

Laurent Pinchart

\
 
 \ /
  Last update: 2017-01-16 16:57    [W:0.658 / U:0.360 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site