lkml.org 
[lkml]   [2017]   [Jan]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH] usb: dwc3: core: Disable USB2.0 phy suspend when dwc3 acts as host role
Date

Hi,

John Youn <John.Youn@synopsys.com> writes:
>> Baolin Wang <baolin.wang@linaro.org> writes:
>>>> Baolin Wang <baolin.wang@linaro.org> writes:
>>>>> When dwc3 controller acts as host role with attaching slow speed device
>>>>> (like mouse or keypad). Then if we plugged out the slow speed device,
>>>>> it will timeout to run the deconfiguration endpoint command to drop the
>>>>> endpoint's resources. Some xHCI command timeout log as below when
>>>>> disconnecting one slow device:
>>>>>
>>>>> [ 99.807739] c0 xhci-hcd.0.auto: Port Status Change Event for port 1
>>>>> [ 99.814699] c0 xhci-hcd.0.auto: resume root hub
>>>>> [ 99.819992] c0 xhci-hcd.0.auto: handle_port_status: starting port
>>>>> polling.
>>>>> [ 99.827808] c0 xhci-hcd.0.auto: get port status, actual port 0 status
>>>>> = 0x202a0
>>>>> [ 99.835903] c0 xhci-hcd.0.auto: Get port status returned 0x10100
>>>>> [ 99.850052] c0 xhci-hcd.0.auto: clear port connect change, actual
>>>>> port 0 status = 0x2a0
>>>>> [ 99.859313] c0 xhci-hcd.0.auto: Cancel URB ffffffc01ed6cd00, dev 1,
>>>>> ep 0x81, starting at offset 0xc406d210
>>>>> [ 99.869645] c0 xhci-hcd.0.auto: // Ding dong!
>>>>> [ 99.874776] c0 xhci-hcd.0.auto: Stopped on Transfer TRB
>>>>> [ 99.880713] c0 xhci-hcd.0.auto: Removing canceled TD starting at
>>>>> 0xc406d210 (dma).
>>>>> [ 99.889012] c0 xhci-hcd.0.auto: Finding endpoint context
>>>>> [ 99.895069] c0 xhci-hcd.0.auto: Cycle state = 0x1
>>>>> [ 99.900519] c0 xhci-hcd.0.auto: New dequeue segment =
>>>>> ffffffc1112f0880 (virtual)
>>>>> [ 99.908655] c0 xhci-hcd.0.auto: New dequeue pointer = 0xc406d220 (DMA)
>>>>> [ 99.915927] c0 xhci-hcd.0.auto: Set TR Deq Ptr cmd, new deq seg =
>>>>> ffffffc1112f0880 (0xc406d000 dma),
>>>>> new deq ptr = ffffff8002175220
>>>>> (0xc406d220 dma), new cycle = 1
>>>>> [ 99.931242] c0 xhci-hcd.0.auto: // Ding dong!
>>>>> [ 99.936360] c0 xhci-hcd.0.auto: Successful Set TR Deq Ptr cmd,
>>>>> deq = @c406d220
>>>>> [ 99.944458] c0 xhci-hcd.0.auto: xhci_hub_status_data: stopping port
>>>>> polling.
>>>>> [ 100.047619] c0 xhci-hcd.0.auto: xhci_drop_endpoint called for udev
>>>>> ffffffc01ae08800
>>>>> [ 100.057002] c0 xhci-hcd.0.auto: drop ep 0x81, slot id 1, new drop
>>>>> flags = 0x8, new add flags = 0x0
>>>>> [ 100.067878] c0 xhci-hcd.0.auto: xhci_check_bandwidth called for udev
>>>>> ffffffc01ae08800
>>>>> [ 100.076868] c0 xhci-hcd.0.auto: New Input Control Context:
>>>>>
>>>>> ......
>>>>>
>>>>> [ 100.427252] c0 xhci-hcd.0.auto: // Ding dong!
>>>>> [ 105.430728] c0 xhci-hcd.0.auto: Command timeout
>>>>> [ 105.436029] c0 xhci-hcd.0.auto: Abort command ring
>>>>> [ 113.558223] c0 xhci-hcd.0.auto: Command completion event does not match
>>>>> command
>>>>> [ 113.569778] c0 xhci-hcd.0.auto: Timeout while waiting for configure
>>>>> endpoint command
>>>>>
>>>>> The reason is it will suspend USB phy to disable phy clock when
>>>>> disconnecting the slow USB decice, that will hang on the xHCI commands
>>>>> executing which depends on the phy clock.
>>>>>
>>>>> Thus we should disable USB2.0 phy suspend feature when dwc3 acts as host
>>>>> role.
>>>>>
>>>>> Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
>>>>> ---
>>>>> drivers/usb/dwc3/core.c | 14 ++++++++++++++
>>>>> 1 file changed, 14 insertions(+)
>>>>>
>>>>> diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
>>>>> index 9a4a5e4..0b646cf 100644
>>>>> --- a/drivers/usb/dwc3/core.c
>>>>> +++ b/drivers/usb/dwc3/core.c
>>>>> @@ -565,6 +565,20 @@ static int dwc3_phy_setup(struct dwc3 *dwc)
>>>>> if (dwc->revision > DWC3_REVISION_194A)
>>>>> reg |= DWC3_GUSB2PHYCFG_SUSPHY;
>>>>>
>>>>> + /*
>>>>> + * When dwc3 controller acts as host role with attaching one slow speed
>>>>> + * device (like mouse or keypad). Then if we plugged out the slow speed
>>>>> + * device, it will timeout to run the deconfiguration endpoint command.
>>>>> + * The reason is it will suspend USB phy to disable phy clock when
>>>>> + * disconnecting slow speed decice, which will affect the xHCI commands
>>>>> + * executing.
>>>>> + *
>>>>> + * Thus we should disable USB 2.0 phy suspend feature when dwc3 acts as
>>>>> + * host role.
>>>>> + */
>>>>> + if (dwc->dr_mode == USB_DR_MODE_HOST || dwc->dr_mode == USB_DR_MODE_OTG)
>>>>> + reg &= ~DWC3_GUSB2PHYCFG_SUSPHY;
>>>>
>>>> which version of the core you're using? Recent version (since 1.94A,
>>>
>>> My version is 2.80a.
>>>
>>>> IIRC) can manage core suspend automatically. Also, this patch of yours
>>>> will cause a power consumption regression.
>>>
>>> Yes, it can manage core suspend automatically, that is the problem.
>>> When plugging out one mouse or keypad device, the phy will suspend
>>> automatically to disable the phy clock. But now the disconnecting
>>> process is not finished, and some xHCI commands (like deconfiguration
>>> endpoint command to drop endpoint resources) need depend on the phy
>>> clock, which will hang on the system to timeout the command or abort
>>> command ring to halt the xHCI.
>>>
>>> I agree with you it will cause a power consumption regression, but it
>>> will cause serious problem if not. Do you have some suggestion?
>>
>> sorry for the long delay. This was lost in my inbox.
>>
>> I'm not sure this patch is the best solution. There's no mention in
>> Databook that we should avoid PHY suspend when acting as host. Adding
>> John here to see if John has any idea of how to fix this.
>>
>
> I'm not familiar enough with XHCI side of things to say.
>
> I'll ask around to see if anyone has an idea.

Thank you

--
balbi
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2017-01-16 11:39    [W:0.057 / U:1.108 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site