lkml.org 
[lkml]   [2016]   [Sep]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    SubjectRe: [PATCH 1/2] pwm: sunxi: allow the pwm to finish its pulse before disable
    From
    Date
    Hi Maxime!,

    On za, 2016-08-27 at 00:19 +0200, Maxime Ripard wrote:
    > On Thu, Aug 25, 2016 at 07:50:10PM +0200, Olliver Schinagl wrote:
    > >
    > > When we inform the PWM block to stop toggeling the output, we may
    > > end up
    > > in a state where the output is not what we would expect (e.g. not
    > > the
    > > low-pulse) but whatever the output was at when the clock got
    > > disabled.
    > >
    > > To counter this we have to wait for maximally the time of one whole
    > > period to ensure the pwm hardware was able to finish. Since we
    > > already
    > > told the PWM hardware to disable it self, it will not continue
    > > toggling
    > > but merly finish its current pulse.
    > >
    > > If a whole period is considered to much, it may be contemplated to
    > > use a
    > > half period + a little bit to ensure we get passed the transition.
    > >
    > > Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
    > > ---
    > >  drivers/pwm/pwm-sun4i.c | 11 +++++++++++
    > >  1 file changed, 11 insertions(+)
    > >
    > > diff --git a/drivers/pwm/pwm-sun4i.c b/drivers/pwm/pwm-sun4i.c
    > > index 03a99a5..5e97c8a 100644
    > > --- a/drivers/pwm/pwm-sun4i.c
    > > +++ b/drivers/pwm/pwm-sun4i.c
    > > @@ -8,6 +8,7 @@
    > >  
    > >  #include <linux/bitops.h>
    > >  #include <linux/clk.h>
    > > +#include <linux/delay.h>
    > >  #include <linux/err.h>
    > >  #include <linux/io.h>
    > >  #include <linux/module.h>
    > > @@ -245,6 +246,16 @@ static void sun4i_pwm_disable(struct pwm_chip
    > > *chip, struct pwm_device *pwm)
    > >   spin_lock(&sun4i_pwm->ctrl_lock);
    > >   val = sun4i_pwm_readl(sun4i_pwm, PWM_CTRL_REG);
    > >   val &= ~BIT_CH(PWM_EN, pwm->hwpwm);
    > > + sun4i_pwm_writel(sun4i_pwm, val, PWM_CTRL_REG);
    > > + spin_unlock(&sun4i_pwm->ctrl_lock);
    > > +
    > > + /* Allow for the PWM hardware to finish its last toggle.
    > > The pulse
    > > +  * may have just started and thus we should wait a full
    > > period.
    > > +  */
    > > + ndelay(pwm_get_period(pwm));
    >
    > Can't that use the ready bit as well?
    It depends whatever is cheaper. If we disable the pwm, we have to
    commit that request to hardware first. Then we have to read back the
    has ready and in the strange situation it is not, wait for it to become
    ready?

    Also, that would mean we would loop in a spin lock, or keep
    setting/clearing an additional spinlock to read the ready bit.

    If that is cheaper then an ndelay, I can rewrite it of course, and
    assuming the 'ready' bit gets set from disabeling the PWM. It needs to
    be investigated if disabeling the PWM, the ready bit is used.q

    >
    > Maxime
    > [unhandled content-type:application/pgp-signature]
    \
     
     \ /
      Last update: 2016-09-17 09:58    [W:2.964 / U:0.084 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site