lkml.org 
[lkml]   [2016]   [Sep]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 1/8] pinctrl: aspeed: "Not enabled" is a significant mux state
On Wed, Sep 28, 2016 at 12:20 AM, Andrew Jeffery <andrew@aj.id.au> wrote:
> Consider a scenario with one pin P that has two signals A and B, where A
> is defined to be higher priority than B: That is, if the mux IP is in a
> state that would consider both A and B to be active on P, then A will be
> the active signal.
>
> To instead configure B as the active signal we must configure the mux so
> that A is inactive. The mux state for signals can be described by
> logical operations on one or more bits from one or more registers (a
> "signal expression"), which in some cases leads to aliased mux states for
> a particular signal. Further, signals described by multi-bit bitfields
> often do not only need to record the states that would make them active
> (the "enable" expressions), but also the states that makes them inactive
> (the "disable" expressions). All of this combined leads to four possible
> states for a signal:
>
> 1. A signal is active with respect to an "enable" expression
> 2. A signal is not active with respect to an "enable" expression
> 3. A signal is inactive with respect to a "disable" expression
> 4. A signal is not inactive with respect to a "disable" expression
>
> In the case of P, if we are looking to activate B without explicitly
> having configured A it's enough to consider A inactive if all of A's
> "enable" signal expressions evaluate to "not active". If any evaluate to
> "active" then the corresponding "disable" states must be applied so it
> becomes inactive.
>
> For example, on the AST2400 the pins composing GPIO bank H provide
> signals ROMD8 through ROMD15 (high priority) and those for UART6 (low
> priority). The mux states for ROMD8 through ROMD15 are aliased, i.e.
> there are two mux states that result in the respective signals being
> configured:
>
> A. SCU90[6]=1
> B. Strap[4,1:0]=100
>
> Further, the second mux state is a 3-bit bitfield that explicitly
> defines the enabled state but the disabled state is implicit, i.e. if
> Strap[4,1:0] is not exactly "100" then ROMD8 through ROMD15 are not
> considered active. This requires the mux function evaluation logic to
> use approach 2. above, however the existing code was using approach 3.
> The problem was brought to light on the Palmetto machines where the
> strap register value is 0x120ce416, and prevented GPIO requests in bank
> H from succeeding despite the hardware being in a position to allow
> them.
>
> Fixes: 318398c09a8d ("pinctrl: Add core pinctrl support for Aspeed SoCs")
> Signed-off-by: Andrew Jeffery <andrew@aj.id.au>

That's a decent commit message.

Reviewed-by: Joel Stanley <joel@jms.id.au>

> ---
> drivers/pinctrl/aspeed/pinctrl-aspeed.c | 12 +++++++-----
> 1 file changed, 7 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/pinctrl/aspeed/pinctrl-aspeed.c b/drivers/pinctrl/aspeed/pinctrl-aspeed.c
> index 0391f9f13f3e..49aeba912531 100644
> --- a/drivers/pinctrl/aspeed/pinctrl-aspeed.c
> +++ b/drivers/pinctrl/aspeed/pinctrl-aspeed.c
> @@ -166,13 +166,9 @@ static bool aspeed_sig_expr_set(const struct aspeed_sig_expr *expr,
> bool enable, struct regmap *map)
> {
> int i;
> - bool ret;
> -
> - ret = aspeed_sig_expr_eval(expr, enable, map);
> - if (ret)
> - return ret;
>
> for (i = 0; i < expr->ndescs; i++) {
> + bool ret;
> const struct aspeed_sig_desc *desc = &expr->descs[i];
> u32 pattern = enable ? desc->enable : desc->disable;
>
> @@ -199,12 +195,18 @@ static bool aspeed_sig_expr_set(const struct aspeed_sig_expr *expr,
> static bool aspeed_sig_expr_enable(const struct aspeed_sig_expr *expr,
> struct regmap *map)
> {
> + if (aspeed_sig_expr_eval(expr, true, map))
> + return true;
> +
> return aspeed_sig_expr_set(expr, true, map);
> }
>
> static bool aspeed_sig_expr_disable(const struct aspeed_sig_expr *expr,
> struct regmap *map)
> {
> + if (!aspeed_sig_expr_eval(expr, true, map))
> + return true;
> +
> return aspeed_sig_expr_set(expr, false, map);
> }
>
> --
> git-series 0.8.10

\
 
 \ /
  Last update: 2016-09-29 02:55    [W:0.468 / U:0.428 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site