lkml.org 
[lkml]   [2016]   [Sep]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [RFC PATCH 08/11] pci: controller: dra7xx: Add EP mode support
From
Date
Hi,

On Friday 23 September 2016 08:22 PM, Rob Herring wrote:
> On Wed, Sep 14, 2016 at 10:42:04AM +0530, Kishon Vijay Abraham I wrote:
>> The PCIe controller integrated in dra7xx SoCs is capable of operating
>> in endpoint mode. Add support for dra7xx SoCs to operate in endpoint
>> mode.
>>
>> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
>> ---
>> Documentation/devicetree/bindings/pci/ti-pci.txt | 30 ++-
>> drivers/pci/controller/Kconfig | 21 +++
>> drivers/pci/controller/pci-dra7xx.c | 211 +++++++++++++++++++---
>> 3 files changed, 225 insertions(+), 37 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt
>> index 60e2516..b0e76f6 100644
>> --- a/Documentation/devicetree/bindings/pci/ti-pci.txt
>> +++ b/Documentation/devicetree/bindings/pci/ti-pci.txt
>> @@ -1,17 +1,22 @@
>> TI PCI Controllers
>>
>> PCIe Designware Controller
>> - - compatible: Should be "ti,dra7-pcie""
>> - - reg : Two register ranges as listed in the reg-names property
>> - - reg-names : The first entry must be "ti-conf" for the TI specific registers
>> - The second entry must be "rc-dbics" for the designware pcie
>> - registers
>> - The third entry must be "config" for the PCIe configuration space
>> + - compatible: Should be "ti,dra7-pcie" for RC
>> + Should be "ti,dra7-pcie-ep" for EP
>> - phys : list of PHY specifiers (used by generic PHY framework)
>> - phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the
>> number of PHYs as specified in *phys* property.
>> - ti,hwmods : Name of the hwmod associated to the pcie, "pcie<X>",
>> where <X> is the instance number of the pcie from the HW spec.
>> + - num-lanes as specified in ../designware-pcie.txt
>> +
>> +HOST MODE
>> +=========
>> + - reg : Two register ranges as listed in the reg-names property
>> + - reg-names : The first entry must be "ti-conf" for the TI specific registers
>> + The second entry must be "rc-dbics" for the designware pcie
>> + registers
>> + The third entry must be "config" for the PCIe configuration space
>> - interrupts : Two interrupt entries must be specified. The first one is for
>> main interrupt line and the second for MSI interrupt line.
>> - #address-cells,
>> @@ -19,13 +24,24 @@ PCIe Designware Controller
>> #interrupt-cells,
>> device_type,
>> ranges,
>> - num-lanes,
>> interrupt-map-mask,
>> interrupt-map : as specified in ../designware-pcie.txt
>>
>> Optional Property:
>> - gpios : Should be added if a gpio line is required to drive PERST# line
>
> Don't you need gpios as the input side of GPIO outputs in RC mode? Or
> for EP mode they are all handled by h/w?

I couldn't find any mention of the gpios being used in EP mode. I'll check this
again.

Thanks
Kishon

\
 
 \ /
  Last update: 2016-09-27 13:36    [W:0.153 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site