lkml.org 
[lkml]   [2016]   [Sep]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v5 7/8] iommu/amd: Don't update domain info to dte entry at iommu init stage
On 09/20/16 at 02:50pm, Joerg Roedel wrote:
> On Thu, Sep 15, 2016 at 11:03:25PM +0800, Baoquan He wrote:
> > AMD iommu creates protection domain and assign each device to it during
> > iommu driver initialization stage. This happened just after system pci
> > bus scanning stage, and much earlier than device driver init stage. So
> > at this time if in kdump kernel the domain info, especially pte_root,
> > can't be updated to dte entry. We should wait until device driver init
> > stage.
> >
> > Signed-off-by: Baoquan He <bhe@redhat.com>
> > ---
> > drivers/iommu/amd_iommu.c | 18 ++++++++++++++++++
> > 1 file changed, 18 insertions(+)
> >
> > diff --git a/drivers/iommu/amd_iommu.c b/drivers/iommu/amd_iommu.c
> > index fcb69ff..6c37300 100644
> > --- a/drivers/iommu/amd_iommu.c
> > +++ b/drivers/iommu/amd_iommu.c
> > @@ -137,6 +137,7 @@ struct iommu_dev_data {
> > bool pri_tlp; /* PASID TLB required for
> > PPR completions */
> > u32 errata; /* Bitmap for errata to apply */
> > + bool domain_updated;
> > };
> >
> > /*
> > @@ -1708,6 +1709,15 @@ static void set_dte_entry(u16 devid, struct protection_domain *domain, bool ats)
> > {
> > u64 pte_root = 0;
> > u64 flags = 0;
> > + struct iommu_dev_data *dev_data;
> > + struct amd_iommu *iommu = amd_iommu_rlookup_table[devid];
> > +
> > + dev_data = find_dev_data(devid);
> > + if (!dev_data)
> > + return;
> > +
> > + if (translation_pre_enabled(iommu) && !dev_data->domain_updated)
> > + return;
> >
> > if (domain->mode != PAGE_MODE_NONE)
> > pte_root = virt_to_phys(domain->pt_root);
> > @@ -1756,6 +1766,14 @@ static void set_dte_entry(u16 devid, struct protection_domain *domain, bool ats)
> >
> > static void clear_dte_entry(u16 devid)
> > {
> > + struct iommu_dev_data *dev_data;
> > + struct amd_iommu *iommu = amd_iommu_rlookup_table[devid];
> > +
> > + dev_data = find_dev_data(devid);
> > + if (!dev_data)
> > + return;
> > + if (translation_pre_enabled(iommu) && !dev_data->domain_updated)
> > + return;
>
> This should be moved to do_attach/do_detach. There you also already have
> the dev_data you need here.

For amd-vi v1, checking in do_attach/do_detach is enough. But for v2
amd_iommu_domain_direct_map and amd_iommu_domain_enable_v2 also call it
to install pte_root into dev table. So finally, I move them into these
two lowest level functions to prevent any pte_root changing during iommu
init stage. It involves the least code change.

>
> > /* remove entry from the device table seen by the hardware */
> > amd_iommu_dev_table[devid].data[0] = DTE_FLAG_V | DTE_FLAG_TV;
> > amd_iommu_dev_table[devid].data[1] &= DTE_FLAG_MASK;
> > --
> > 2.5.5
> >

\
 
 \ /
  Last update: 2016-09-22 23:58    [W:0.077 / U:0.268 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site