lkml.org 
[lkml]   [2016]   [Aug]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[RFC PATCH 5/5] arm64: dts: sunxi: add MMC nodes to Pine64 and BPi-M64 .dts
Date
Those two boards connect a microSD card slot to the MMC0 controller.
Add the dummy regulator and enable MMC0 to allow accessing the SD card.

The BananaPi M64 has an on-board eMMC chip connected to the MMC2
controller, but the existing MMC driver does not support this properly
yet, so keep this one disabled for now.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
.../boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 29 ++++++++++++++++++++++
.../arm64/boot/dts/allwinner/sun50i-a64-pine64.dts | 20 +++++++++++++++
2 files changed, 49 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
index bc0ed4c..f98c351 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
@@ -59,6 +59,35 @@
aliases {
serial0 = &uart0;
};
+
+ soc {
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>, <&mmc0_default_cd_pin>;
+ bus-width = <4>;
+ vmmc-supply = <&reg_vcc3v3>;
+ cd-gpios = <&pio 5 6 0>;
+ cd-inverted;
+ disable-wp;
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+ bus-width = <8>;
+ vmmc-supply = <&reg_vcc3v3>;
+ non-removable;
+ status = "disabled";
};

&uart0 {
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
index 077a56f..a3957ca 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
@@ -59,6 +59,26 @@
aliases {
serial0 = &uart0;
};
+
+ soc {
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>, <&mmc0_default_cd_pin>;
+ bus-width = <4>;
+ vmmc-supply = <&reg_vcc3v3>;
+ cd-gpios = <&pio 5 6 0>;
+ cd-inverted;
+ disable-wp;
+ status = "okay";
};

&uart0 {
--
2.9.0
\
 
 \ /
  Last update: 2016-08-09 14:21    [W:0.293 / U:0.100 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site