lkml.org 
[lkml]   [2016]   [Aug]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/3] Documentation: dtb: xgene: Add PMD clock binding
On Tue, Aug 23, 2016 at 08:52:39AM -0700, Hoan Tran wrote:
> Add APM X-Gene clock binding documentation for PMD clock.
>
> Signed-off-by: Hoan Tran <hotran@apm.com>
> ---
> Documentation/devicetree/bindings/clock/xgene.txt | 22 ++++++++++++++++++++++
> 1 file changed, 22 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/clock/xgene.txt b/Documentation/devicetree/bindings/clock/xgene.txt
> index 82f9638..c381733 100644
> --- a/Documentation/devicetree/bindings/clock/xgene.txt
> +++ b/Documentation/devicetree/bindings/clock/xgene.txt
> @@ -8,6 +8,7 @@ Required properties:
> - compatible : shall be one of the following:
> "apm,xgene-socpll-clock" - for a X-Gene SoC PLL clock
> "apm,xgene-pcppll-clock" - for a X-Gene PCP PLL clock
> + "apm,xgene-pmd-clock" - for a X-Gene PMD clock
> "apm,xgene-device-clock" - for a X-Gene device clock
> "apm,xgene-socpll-v2-clock" - for a X-Gene SoC PLL v2 clock
> "apm,xgene-pcppll-v2-clock" - for a X-Gene PCP PLL v2 clock
> @@ -22,6 +23,17 @@ Required properties for SoC or PCP PLL clocks:
> Optional properties for PLL clocks:
> - clock-names : shall be the name of the PLL. If missing, use the device name.
>
> +Required properties for PMD clocks:
> +- reg : shall be the physical register address for the pmd clock.
> +- clocks : shall be the input parent clock phandle for the clock.
> +- #clock-cells : shall be set to 1.
> +- clock-output-names : shall be the name of the clock referenced by derive
> + clock.
> +- clock-shift: Bit shift of the clock register. Default is 0.
> +- clock-width: Width of the clock register. Default is 32.
> +Optional properties for PLL clocks:
> +- clock-names : shall be the name of the clock. If missing, use the device name.
> +
> Required properties for device clocks:
> - reg : shall be a list of address and length pairs describing the CSR
> reset and/or the divider. Either may be omitted, but at least
> @@ -59,6 +71,16 @@ For example:
> type = <0>;
> };
>
> + pmd0clk: pmd0clk {
> + compatible = "apm,xgene-pmd-clock";
> + #clock-cells = <1>;
> + clocks = <&pmdpll 0>;
> + reg = <0x0 0x7E200200 0x0 0x10>;
> + clock-shift = <8>;
> + clock-width = <3>;

These should be implied by the compatible string. It's not a big deal
for just adding this clock, but if you have lots more clocks to add then
it is a problem. We only want leaf clocks (the ones going to devices) in
DT unless there is only a few clocks.

Rob

\
 
 \ /
  Last update: 2016-09-17 09:58    [W:0.052 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site