lkml.org 
[lkml]   [2016]   [Jul]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 05/22] usb: serial: ti_usb_3410_5052: Use C_X macros instead of c_cflag manipulation
Date
Use C_X tty.h macros to avoid direct manipulation of termios
c_cflag variable.

Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
---
drivers/usb/serial/ti_usb_3410_5052.c | 16 ++++++++--------
1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/drivers/usb/serial/ti_usb_3410_5052.c b/drivers/usb/serial/ti_usb_3410_5052.c
index c8ed3f9..29bb62c 100644
--- a/drivers/usb/serial/ti_usb_3410_5052.c
+++ b/drivers/usb/serial/ti_usb_3410_5052.c
@@ -955,7 +955,7 @@ static void ti_set_termios(struct tty_struct *tty,
wflags |= TI_UART_ENABLE_AUTO_START_DMA;
config->bUartMode = tport->tp_uart_mode;

- switch (cflag & CSIZE) {
+ switch (C_CSIZE(tty)) {
case CS5:
config->bDataBits = TI_UART_5_DATA_BITS;
break;
@@ -974,8 +974,8 @@ static void ti_set_termios(struct tty_struct *tty,
/* CMSPAR isn't supported by this driver */
tty->termios.c_cflag &= ~CMSPAR;

- if (cflag & PARENB) {
- if (cflag & PARODD) {
+ if (C_PARENB(tty)) {
+ if (C_PARODD(tty)) {
wflags |= TI_UART_ENABLE_PARITY_CHECKING;
config->bParity = TI_UART_ODD_PARITY;
} else {
@@ -987,14 +987,14 @@ static void ti_set_termios(struct tty_struct *tty,
config->bParity = TI_UART_NO_PARITY;
}

- if (cflag & CSTOPB)
+ if (C_CSTOPB(tty))
config->bStopBits = TI_UART_2_STOP_BITS;
else
config->bStopBits = TI_UART_1_STOP_BITS;

- if (cflag & CRTSCTS) {
+ if (C_CRTSCTS(tty)) {
/* RTS flow control must be off to drop RTS for baud rate B0 */
- if ((cflag & CBAUD) != B0)
+ if ((C_BAUD(tty)) != B0)
wflags |= TI_UART_ENABLE_RTS_IN;
wflags |= TI_UART_ENABLE_CTS_OUT;
} else {
@@ -1023,7 +1023,7 @@ static void ti_set_termios(struct tty_struct *tty,
wbaudrate = (461538 + baud/2) / baud;

/* FIXME: Should calculate resulting baud here and report it back */
- if ((cflag & CBAUD) != B0)
+ if ((C_BAUD(tty)) != B0)
tty_encode_baud_rate(tty, baud, baud);

dev_dbg(&port->dev,
@@ -1045,7 +1045,7 @@ static void ti_set_termios(struct tty_struct *tty,
/* SET_CONFIG asserts RTS and DTR, reset them correctly */
mcr = tport->tp_shadow_mcr;
/* if baud rate is B0, clear RTS and DTR */
- if ((cflag & CBAUD) == B0)
+ if (C_BAUD(tty) == B0)
mcr &= ~(TI_MCR_DTR | TI_MCR_RTS);
status = ti_set_mcr(tport, mcr);
if (status)
--
2.9.0
\
 
 \ /
  Last update: 2016-07-26 21:01    [W:0.259 / U:0.084 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site