lkml.org 
[lkml]   [2016]   [Jun]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v3 2/8] mfd: ac100: Add device tree bindings for X-Powers AC100 codec/RTC combo IC
On Tue, Jun 21, 2016 at 9:14 PM, Rob Herring <robh@kernel.org> wrote:
> On Mon, Jun 20, 2016 at 10:52:12AM +0800, Chen-Yu Tsai wrote:
>> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
>> ---
>> Changes since v2:
>>
>> - Fix interrupt line for ac100_codec in provided example.
>>
>> ---
>> Documentation/devicetree/bindings/mfd/ac100.txt | 42 +++++++++++++++++++++++++
>> 1 file changed, 42 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/mfd/ac100.txt
>>
>> diff --git a/Documentation/devicetree/bindings/mfd/ac100.txt b/Documentation/devicetree/bindings/mfd/ac100.txt
>> new file mode 100644
>> index 000000000000..a793954bb952
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/mfd/ac100.txt
>> @@ -0,0 +1,42 @@
>> +X-Powers AC100 Codec/RTC IC device tree bindings
>> +
>> +AC100 is a audio codec and RTC subsystem combo IC. The 2 parts are
>> +separated, including power supplies and interrupt lines, but share
>> +a common register address space and host interface.
>> +
>> +Required properties:
>> +- compatible: "x-powers,ac100"
>> +- reg: The I2C slave address or RSB hardware address for the chip
>> +- sub-nodes:
>> + - codec
>> + - compatible: "x-powers,ac100-codec"
>> + - interrupt-parent: The parent interrupt controller
>> + - interrupts: SoC NMI / GPIO interrupt connected to the IRQ_AUDIO pin
>> + - rtc
>> + - compatible: "x-powers,ac100-rtc"
>> + - interrupt-parent: The parent interrupt controller
>> + - interrupts: SoC NMI / GPIO interrupt connected to the IRQ_RTC pin
>> + - #clock-cells: shall be 1
>> + - clock-output-names: "cko1_rtc", "cko2_rtc", "cko3_rtc"
>> + - see clock/clock-bindings.txt for common clock bindings
>> +
>> +Example:
>> +
>> +ac100: codec@e89 {
>> + compatible = "x-powers,ac100";
>> + reg = <0xe89>;
>> +
>> + ac100_codec {
>
> Use generic node names and no underscores:
>
> codec {

Right. I intended to add them as labels, not change the node names.

Thanks
ChenYu

>
>> + compatible = "x-powers,ac100-codec";
>> + interrupt-parent = <&r_pio>;
>> + interrupts = <0 9 IRQ_TYPE_LEVEL_LOW>; /* PL9 */
>> + };
>> +
>> + ac100_rtc {
>
> rtc {
>
>> + compatible = "x-powers,ac100-rtc";
>> + interrupt-parent = <&nmi_intc>;
>> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
>> + #clock-cells = <1>;
>> + clock-output-names = "cko1_rtc", "cko2_rtc", "cko3_rtc";
>> + };
>> +};
>> --
>> 2.8.1
>>

\
 
 \ /
  Last update: 2016-06-22 07:01    [W:0.050 / U:1.220 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site