lkml.org 
[lkml]   [2016]   [Jun]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/4] Staging: comedi: dt2815: Comment issue fixed
Date
This fixes up a WARNING: 'Block comments use a trailing */ on a
separate line' found by the checkpatch.pl tool.

Signed-off-by: Ravishankar Karkala Mallikarjunayya <ravishankarkm32@gmail.com>
---
drivers/staging/comedi/drivers/dt2815.c | 140 ++++++++++++++++----------------
1 file changed, 70 insertions(+), 70 deletions(-)

diff --git a/drivers/staging/comedi/drivers/dt2815.c b/drivers/staging/comedi/drivers/dt2815.c
index fb08569..0be77cc 100644
--- a/drivers/staging/comedi/drivers/dt2815.c
+++ b/drivers/staging/comedi/drivers/dt2815.c
@@ -1,55 +1,55 @@
/*
- comedi/drivers/dt2815.c
- Hardware driver for Data Translation DT2815
-
- COMEDI - Linux Control and Measurement Device Interface
- Copyright (C) 1999 Anders Blomdell <anders.blomdell@control.lth.se>
-
- This program is free software; you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation; either version 2 of the License, or
- (at your option) any later version.
-
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
+ * comedi/drivers/dt2815.c
+ * Hardware driver for Data Translation DT2815
+ *
+ * COMEDI - Linux Control and Measurement Device Interface
+ * Copyright (C) 1999 Anders Blomdell <anders.blomdell@control.lth.se>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
*/
/*
-Driver: dt2815
-Description: Data Translation DT2815
-Author: ds
-Status: mostly complete, untested
-Devices: [Data Translation] DT2815 (dt2815)
-
-I'm not sure anyone has ever tested this board. If you have information
-contrary, please update.
-
-Configuration options:
- [0] - I/O port base base address
- [1] - IRQ (unused)
- [2] - Voltage unipolar/bipolar configuration
- 0 == unipolar 5V (0V -- +5V)
- 1 == bipolar 5V (-5V -- +5V)
- [3] - Current offset configuration
- 0 == disabled (0mA -- +32mAV)
- 1 == enabled (+4mA -- +20mAV)
- [4] - Firmware program configuration
- 0 == program 1 (see manual table 5-4)
- 1 == program 2 (see manual table 5-4)
- 2 == program 3 (see manual table 5-4)
- 3 == program 4 (see manual table 5-4)
- [5] - Analog output 0 range configuration
- 0 == voltage
- 1 == current
- [6] - Analog output 1 range configuration (same options)
- [7] - Analog output 2 range configuration (same options)
- [8] - Analog output 3 range configuration (same options)
- [9] - Analog output 4 range configuration (same options)
- [10] - Analog output 5 range configuration (same options)
- [11] - Analog output 6 range configuration (same options)
- [12] - Analog output 7 range configuration (same options)
-*/
+ * Driver: dt2815
+ * Description: Data Translation DT2815
+ * Author: ds
+ * Status: mostly complete, untested
+ * Devices: [Data Translation] DT2815 (dt2815)
+ *
+ * I'm not sure anyone has ever tested this board. If you have information
+ * contrary, please update.
+ *
+ * Configuration options:
+ * [0] - I/O port base base address
+ * [1] - IRQ (unused)
+ * [2] - Voltage unipolar/bipolar configuration
+ * 0 == unipolar 5V (0V -- +5V)
+ * 1 == bipolar 5V (-5V -- +5V)
+ * [3] - Current offset configuration
+ * 0 == disabled (0mA -- +32mAV)
+ * 1 == enabled (+4mA -- +20mAV)
+ * [4] - Firmware program configuration
+ * 0 == program 1 (see manual table 5-4)
+ * 1 == program 2 (see manual table 5-4)
+ * 2 == program 3 (see manual table 5-4)
+ * 3 == program 4 (see manual table 5-4)
+ * [5] - Analog output 0 range configuration
+ * 0 == voltage
+ * 1 == current
+ * [6] - Analog output 1 range configuration (same options)
+ * [7] - Analog output 2 range configuration (same options)
+ * [8] - Analog output 3 range configuration (same options)
+ * [9] - Analog output 4 range configuration (same options)
+ * [10] - Analog output 5 range configuration (same options)
+ * [11] - Analog output 6 range configuration (same options)
+ * [12] - Analog output 7 range configuration (same options)
+ */

#include <linux/module.h>
#include "../comedidev.h"
@@ -120,27 +120,27 @@ static int dt2815_ao_insn(struct comedi_device *dev, struct comedi_subdevice *s,
}

/*
- options[0] Board base address
- options[1] IRQ (not applicable)
- options[2] Voltage unipolar/bipolar configuration
- 0 == unipolar 5V (0V -- +5V)
- 1 == bipolar 5V (-5V -- +5V)
- options[3] Current offset configuration
- 0 == disabled (0mA -- +32mAV)
- 1 == enabled (+4mA -- +20mAV)
- options[4] Firmware program configuration
- 0 == program 1 (see manual table 5-4)
- 1 == program 2 (see manual table 5-4)
- 2 == program 3 (see manual table 5-4)
- 3 == program 4 (see manual table 5-4)
- options[5] Analog output 0 range configuration
- 0 == voltage
- 1 == current
- options[6] Analog output 1 range configuration
- ...
- options[12] Analog output 7 range configuration
- 0 == voltage
- 1 == current
+ * options[0] Board base address
+ * options[1] IRQ (not applicable)
+ * options[2] Voltage unipolar/bipolar configuration
+ * 0 == unipolar 5V (0V -- +5V)
+ * 1 == bipolar 5V (-5V -- +5V)
+ * options[3] Current offset configuration
+ * 0 == disabled (0mA -- +32mAV)
+ * 1 == enabled (+4mA -- +20mAV)
+ * options[4] Firmware program configuration
+ * 0 == program 1 (see manual table 5-4)
+ * 1 == program 2 (see manual table 5-4)
+ * 2 == program 3 (see manual table 5-4)
+ * 3 == program 4 (see manual table 5-4)
+ * options[5] Analog output 0 range configuration
+ * 0 == voltage
+ * 1 == current
+ * options[6] Analog output 1 range configuration
+ * ...
+ * options[12] Analog output 7 range configuration
+ * 0 == voltage
+ * 1 == current
*/

static int dt2815_attach(struct comedi_device *dev, struct comedi_devconfig *it)
--
1.9.1
\
 
 \ /
  Last update: 2016-06-17 14:01    [W:0.062 / U:0.928 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site