lkml.org 
[lkml]   [2016]   [May]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 3/3] clk: bcm2835: Skip PLLC clocks when deciding on a new clock parent
Date
If the firmware had set up a clock to source from PLLC, go along with
it. But if we're looking for a new parent, we don't want to switch it
to PLLC because the firmware will force PLLC (and thus the AXI bus
clock) to different frequencies during over-temp/under-voltage,
without notification to Linux.

On my system, this moves the Linux-enabled HDMI state machine and DSI1
escape clock over to plld_per from pllc_per. EMMC still ends up on
pllc_per, because the firmware had set it up to use that.

Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the audio domain clocks")
---

No changes, just a resend.

drivers/clk/bcm/clk-bcm2835.c | 23 +++++++++++++++++++++++
1 file changed, 23 insertions(+)

diff --git a/drivers/clk/bcm/clk-bcm2835.c b/drivers/clk/bcm/clk-bcm2835.c
index 1091012ecec6..1d8f29ea9f69 100644
--- a/drivers/clk/bcm/clk-bcm2835.c
+++ b/drivers/clk/bcm/clk-bcm2835.c
@@ -1008,16 +1008,28 @@ static int bcm2835_clock_set_rate(struct clk_hw *hw,
return 0;
}

+static bool
+bcm2835_clk_is_pllc(struct clk_hw *hw)
+{
+ if (!hw)
+ return false;
+
+ return strncmp(clk_hw_get_name(hw), "pllc", 4) == 0;
+}
+
static int bcm2835_clock_determine_rate(struct clk_hw *hw,
struct clk_rate_request *req)
{
struct bcm2835_clock *clock = bcm2835_clock_from_hw(hw);
struct clk_hw *parent, *best_parent = NULL;
+ bool current_parent_is_pllc;
unsigned long rate, best_rate = 0;
unsigned long prate, best_prate = 0;
size_t i;
u32 div;

+ current_parent_is_pllc = bcm2835_clk_is_pllc(clk_hw_get_parent(hw));
+
/*
* Select parent clock that results in the closest but lower rate
*/
@@ -1025,6 +1037,17 @@ static int bcm2835_clock_determine_rate(struct clk_hw *hw,
parent = clk_hw_get_parent_by_index(hw, i);
if (!parent)
continue;
+
+ /*
+ * Don't choose a PLLC-derived clock as our parent
+ * unless it had been manually set that way. PLLC's
+ * frequency gets adjusted by the firmware due to
+ * over-temp or under-voltage conditions, without
+ * prior notification to our clock consumer.
+ */
+ if (bcm2835_clk_is_pllc(parent) && !current_parent_is_pllc)
+ continue;
+
prate = clk_hw_get_rate(parent);
div = bcm2835_clock_choose_div(hw, req->rate, prate, true);
rate = bcm2835_clock_rate_from_divisor(clock, prate, div);
--
2.8.0.rc3
\
 
 \ /
  Last update: 2016-05-10 03:21    [W:0.139 / U:0.200 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site