lkml.org 
[lkml]   [2016]   [May]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH V7 00/11] Support for generic ACPI based PCI host controller
Date
A big +1 to the below :) :) :)

--
Computer Architect | Sent from my 64-bit #ARM Powered phone

> On May 24, 2016, at 13:24, Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> wrote:
>
> Hi Bjorn,
>
> On Mon, May 23, 2016 at 06:39:18PM -0500, Bjorn Helgaas wrote:
>
> [...]
>
>> On Mon, May 23, 2016 at 03:16:01PM +0000, Gabriele Paoloni wrote:
>> I don't think of ECAM support itself as a "driver". It's just a
>> service available to drivers, similar to OF resource parsing.
>>
>> Per PCI Firmware r3.2, sec 4.1.5, "PNP0A03" means a PCI/PCI-X/PCIe
>> host bridge. "PNP0A08" means a PCI-X Mode 2 or PCIe bridge that
>> supports extended config space. It doesn't specify how we access that
>> config space, so I think hardware with non-standard ECAM should still
>> have PNP0A03 and PNP0A08 in _CID or _HID.
>>
>> "ECAM" as used in the specs (PCIe r3.0, sec 7.2.2, and PCI Firmware
>> r3.2, sec 4.1) means:
>>
>> (a) a memory-mapped model for config space access, and
>> (b) a specific mapping of address bits to bus/device/function/
>> register
>>
>> MCFG and _CBA assume both (a) and (b), so I think a device with
>> non-standard ECAM mappings should not be described in MCFG or _CBA.
>>
>> If a bridge has ECAM with non-standard mappings, I think either a
>> vendor-specific _HID or a device-specific method, e.g., _DSM, could
>> communicate that.
>>
>> Jon, I agree that we should avoid describing non-standardized hardware
>> in Linux-specific ways. Is there a mechanism in use already? How
>> does Windows handle this? DMI is a poor long-term solution because it
>> requires ongoing maintenance for new platforms, but I think it's OK
>> for getting started with platforms already shipping.
>>
>> A _DSM has the advantage that once it is defined and supported, OEMs
>> can ship new platforms without requiring a new quirk or a new _HID to
>> be added to a driver.
>>
>> There would still be the problem of config access before the namespace
>> is available, i.e., the MCFG use case. I don't know how important
>> that is. Defining an MCFG extension seems like the most obvious
>> solution.
>
> Your summary above is a perfect representation of the situation.
>
> We had an opportunity to sync-up on the current status of ACPI PCI
> for ARM64 (and talked about a way forward for this series, which
> includes quirks handling), let me summarize it here for everyone
> involved so that we can agree on a way forward.
>
> 1) ACPI PCI support for PNP0A03/PNP0A08 host bridges on top of MCFG
> ECAM for config space is basically ready (Tomasz and JC addressed
> Rafael's concerns in relation to ARM64 specific code, and managed
> to find a way to allocate domain numbers in preparation for Arnd
> pci_create_root_bus() clean-up, v8 to be posted shortly and should
> be final). This provides support for de-facto ACPI/PCI ECAM base
> standard for ARM64 (with a clean-split between generic code and ARM64
> bits, where ARM64, like X86 and IA64, manages in arch code IO space and
> PCI resources, to be further consolidated in the near future).
> I do not think anyone can complain about the generality of what we
> achieved, for systems that are PCI standard (yes, PCI STANDARD) this
> would just be sufficient.
> 2) In a real world (1) is not enough. Some ARM64 platforms, not entirely
> ECAM compliant, already shipped with the corresponding firmware that
> we can't update. HW has ECAM quirks and to work around it in the kernel
> we put forward many solutions to the problem, it is time we found a
> solution (when, of course, (1) is completed and upstream).
> Using the MCFG table OEMID matching floated around in this thread
> would work fine for most of the platforms (and cross-OS) that have
> shipped with HW ECAM quirks, so I think that's the starting point for
> our solution and that's how we can sort this out, _today_.
>
> The solution is a trivial look-up table:
> MCFG OEMID <-> PCI config space ops
>
> 3) (2) does not just work on some platforms (and we can't predict the
> future either - actually I can, it is three letters, ECAM), simply
> because MCFG OEMID matching does not provide a way to attach further
> data to the MCFG (eg if config space for, say, bus 0 domain 0, is not
> ECAM compliant, the config region can't be handled and must not be
> handled through a corresponding MCFG region.
> That's the problem Gabriele is facing and wants to solve through
> something like:
>
> https://lkml.org/lkml/2016/3/9/91
>
> in the respective ACPI tables-bindings. It may be an idea worth
> pursuing, it does not solve (2) simply because that FW has shipped,
> we can't patch it any longer.
>
> Hence to finally support ACPI PCI on ARM64 I suggest we carry out the
> following steps, in order:
>
> - Let's complete/merge (1), that's fundamental to this whole thread
> - On top of (1) we apply a quirking mechanism based on (2) that allows
> us to boot mainline with boxes shipping today with no FW update required.
> - We devise a way to handle quirks that is more generic than (2) so that
> can we can accomodate further platforms that can't rely on (2) but
> have more leeway in terms of FW updates.
>
> I hope that's a reasonable plan, Tomasz's v8 series coming to kick it off.
>
> Thank you,
> Lorenzo

\
 
 \ /
  Last update: 2016-05-24 20:01    [W:0.279 / U:0.372 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site