lkml.org 
[lkml]   [2016]   [May]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [RFC6 PATCH v6 00/21] ILP32 for ARM64
On Fri, May 13, 2016 at 04:11:23PM +0800, Zhangjian (Bamvor) wrote:
> On 2016/5/12 23:28, Catalin Marinas wrote:
> >On Thu, May 12, 2016 at 05:24:57PM +0300, Yury Norov wrote:
> >>On Thu, May 12, 2016 at 03:07:35PM +0100, Catalin Marinas wrote:
> >>>On Thu, May 12, 2016 at 04:44:31PM +0300, Yury Norov wrote:
> >>>>On Thu, May 12, 2016 at 02:35:34PM +0100, Catalin Marinas wrote:
> >>>>>On Thu, May 12, 2016 at 03:20:00AM +0300, Yury Norov wrote:
> >>>>>>I debugged preadv02 and pwritev02 failures and found very weird bug.
> >>>>>>Test passes {iovec_base = 0xffffffff, iovec_len = 64} as one element
> >>>>>>of vector, and kernel reports successful read/write.
> >>>>>>
> >>>>>>There are 2 problems:
> >>>>>>1. How kernel allows such address to be passed to fs subsystem;
> >>>>>>2. How fs successes to read/write at non-mapped, and in fact non-user
> >>>>>>address.
> >>>>>>
> >>>>>>I don't know the answer on 2'nd question, and it might be something
> >>>>>>generic. But I investigated first problem.
> >>>>>>
> >>>>>>The problem is that compat_rw_copy_check_uvector() uses access_ok() to
> >>>>>>validate user address, and on arm64 it ends up with checking buffer
> >>>>>>end against current_thread_info()->addr_limit.
> >>>>>>
> >>>>>>current_thread_info()->addr_limit for ilp32, and most probably for
> >>>>>>aarch32 is equal to aarch64 one, and so adress_ok() doesn't fail.
> >>>>>>It happens because on thread creation we call flush_old_exec() to set
> >>>>>>addr_limit, and completely ignore compat mode there.
[...]
> >>>>That's true, but USER_DS depends on personality which is not set yet
> >>>>for new thread, as I wrote above. In fact, I tried correct USER_DS
> >>>>only, and it doesn't work
> >>>
> >>>Ah, it looks like load_elf_binary() sets the personality after
> >>>flush_old_exec(). Looking at powerpc and x86, they set USER_DS to the
> >>>maximum 64-bit task value, so they should have a similar issue with
> >>>native 32-bit vs compat behaviour.
[...]
> >>>So what exactly is LTP complaining about? Is different error (like
> >>>EFAULT vs EINVAL) or not getting an error at all.
> >>
> >>It should be EINVAL, but it succeed. The other problem is that
> >>following fs routines does not complain on wrong address.
> >
> >I see. The test asks the kernel to write a single byte (out of maximum
> >64) to the user address 0xffffffff.
>
> What address We should set for this limitation, TASK_SIZE or STACK_TOP?
> It is same for 64bit application. But STACK_TOP(0xffff0000) is below
> TASK_SIZE in 32bit application. The address above STACK_TOP is preserved
> for 32bit application.

The discussion is mainly around whether USER_DS for 32-bit compat apps
should be the same as USER_DS for native 32-bit apps. Even for native
32-bit kernels, we don't use STACK_TOP as addr_limit. A read/write from
0xffffffff would fail in both cases anyway. I think the LTP test doesn't
even try to access such memory but only to probe the range validity (I
haven't managed to build the latest LTP yet).

--
Catalin

\
 
 \ /
  Last update: 2016-05-13 12:01    [W:0.261 / U:0.056 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site