lkml.org 
[lkml]   [2016]   [May]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: [PATCH 2/2] clk: rockchip: fix the rk3399 sdmmc sample shift
From
Date
在 2016/5/13 7:10, Brian Norris 写道:
> On Thu, May 12, 2016 at 11:03:17AM -0700, Doug Anderson wrote:
>> Just like every other Rockhip device, the MMC "_sample" clocks should
>> have a shift of 0, not a shift of 1. The rk3399 TRM agrees. Presumably
>> these values were set to 0 because of a typo.
>
> I'll semi-disagree about the TRM: the TRM doesn't seem to agree with
> itself, so it sometimes agrees with you and sometimes doesn't :)
>
> On page 79 of the 2nd (?) book, it looks like {SDMMC,SDIO}_CON{0,}[2:1]
> are {drv,sample}_degree. But on page 208 of the 1st book, those are put
> at bits [1:0].
>


Please refer to Mobile Strorage Host Controller section for anything
about sdmmc/sdio. So shift should be 1.

Sometime I also get bothered to address it. Anyway, I will always keep
a eye on it from now on.....

> Perhaps we can get a straight answer from Rockchip though.
>
> Brian
>
>> Things _sorta_ would have worked with the incorrect sample phase shift
>> because of the register layout but wouldn't have been ideal and we would
>> have skipped lots of phases. Also: we would never actually enabled the
>> fine delay unless we happened to have 128 or more delay elements.
>>
>> This is expected behavior before this patch:
>> * Try to set: 0 degrees + 1 delay elements
>> Actually get: 0 degrees + 0 delay elements
>> * Try to set: 90 degrees + 0 delay elements
>> Actually get: 180 degrees + 0 delay elements
>> * Try to set: 180 degrees + 0 delay elements
>> Actually get: 0 degrees + 0 delay elements
>> * Try to set: 270 degrees + 0 delay elements
>> Actually get: 180 degrees + 0 delay elements
>> * Try to set: 0 degrees + 129 delay elements
>> Actually get: 0 degrees + 2 delay elements
>> * Try to set: 180 degrees + 129 delay elements
>> Actually get: 0 degrees + 3 delay elements
>> * Try to set: 0 degrees + 130 delay elements
>> Actually get: 0 degrees + 4 delay elements
>>
>> I verified that old code had a problem by turning on debug printouts and
>> seeing that the old code would report this for one SD card I had:
>> Good phase range 347-101 (115 len)
>> Good phase range 202-326 (125 len)
>>
>> After my fix, it went down to one big good range for the same card.
>> This is more expected:
>> Good phase range 189-1 (173 len)
>> Good phase range 82-85 (4 len)
>> Good phase range 166-168 (3 len)
>>
>> Signed-off-by: Douglas Anderson <dianders@chromium.org>
>> ---
>> drivers/clk/rockchip/clk-rk3399.c | 4 ++--
>> 1 file changed, 2 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/clk/rockchip/clk-rk3399.c b/drivers/clk/rockchip/clk-rk3399.c
>> index 291543f52caa..14ff3e109e1e 100644
>> --- a/drivers/clk/rockchip/clk-rk3399.c
>> +++ b/drivers/clk/rockchip/clk-rk3399.c
>> @@ -895,10 +895,10 @@ static struct rockchip_clk_branch rk3399_clk_branches[] __initdata = {
>> RK3399_CLKGATE_CON(6), 1, GFLAGS),
>>
>> MMC(SCLK_SDMMC_DRV, "sdmmc_drv", "clk_sdmmc", RK3399_SDMMC_CON0, 1),
>> - MMC(SCLK_SDMMC_SAMPLE, "sdmmc_sample", "clk_sdmmc", RK3399_SDMMC_CON1, 1),
>> + MMC(SCLK_SDMMC_SAMPLE, "sdmmc_sample", "clk_sdmmc", RK3399_SDMMC_CON1, 0),
>>
>> MMC(SCLK_SDIO_DRV, "sdio_drv", "clk_sdio", RK3399_SDIO_CON0, 1),
>> - MMC(SCLK_SDIO_SAMPLE, "sdio_sample", "clk_sdio", RK3399_SDIO_CON1, 1),
>> + MMC(SCLK_SDIO_SAMPLE, "sdio_sample", "clk_sdio", RK3399_SDIO_CON1, 0),
>>
>> /* pcie */
>> COMPOSITE(SCLK_PCIE_PM, "clk_pcie_pm", mux_pll_src_cpll_gpll_npll_24m_p, 0,
>
>
>


--
Best Regards
Shawn Lin

\
 
 \ /
  Last update: 2016-05-13 02:21    [W:0.141 / U:0.024 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site