lkml.org 
[lkml]   [2016]   [May]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/4] phy: rockchip-emmc: configure frequency range and drive impedance
Date
From: Shawn Lin <shawn.lin@rock-chips.com>

Signal integrity analysis has suggested we set these values. Do this in
power_on(), so that they get reconfigured after suspend/resume.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
---
drivers/phy/phy-rockchip-emmc.c | 27 +++++++++++++++++++++++++++
1 file changed, 27 insertions(+)

diff --git a/drivers/phy/phy-rockchip-emmc.c b/drivers/phy/phy-rockchip-emmc.c
index 48cbe691a889..5641dede32f6 100644
--- a/drivers/phy/phy-rockchip-emmc.c
+++ b/drivers/phy/phy-rockchip-emmc.c
@@ -56,6 +56,19 @@
#define PHYCTRL_DLLRDY_SHIFT 0x5
#define PHYCTRL_DLLRDY_DONE 0x1
#define PHYCTRL_DLLRDY_GOING 0x0
+#define PHYCTRL_FREQSEL_200M 0x0
+#define PHYCTRL_FREQSEL_50M 0x1
+#define PHYCTRL_FREQSEL_100M 0x2
+#define PHYCTRL_FREQSEL_150M 0x3
+#define PHYCTRL_FREQSEL_MASK 0x3
+#define PHYCTRL_FREQSEL_SHIFT 0xc
+#define PHYCTRL_DR_MASK 0x7
+#define PHYCTRL_DR_SHIFT 0x4
+#define PHYCTRL_DR_50OHM 0x0
+#define PHYCTRL_DR_33OHM 0x1
+#define PHYCTRL_DR_66OHM 0x2
+#define PHYCTRL_DR_100OHM 0x3
+#define PHYCTRL_DR_40OHM 0x4

struct rockchip_emmc_phy {
unsigned int reg_offset;
@@ -154,6 +167,20 @@ static int rockchip_emmc_phy_power_on(struct phy *phy)
struct rockchip_emmc_phy *rk_phy = phy_get_drvdata(phy);
int ret = 0;

+ /* DLL operation: 170 to 200 MHz */
+ regmap_write(rk_phy->reg_base,
+ rk_phy->reg_offset + GRF_EMMCPHY_CON0,
+ HIWORD_UPDATE(PHYCTRL_FREQSEL_200M,
+ PHYCTRL_FREQSEL_MASK,
+ PHYCTRL_FREQSEL_SHIFT));
+
+ /* Drive impedance: 50 Ohm */
+ regmap_write(rk_phy->reg_base,
+ rk_phy->reg_offset + GRF_EMMCPHY_CON6,
+ HIWORD_UPDATE(PHYCTRL_DR_50OHM,
+ PHYCTRL_DR_MASK,
+ PHYCTRL_DR_SHIFT));
+
/* Power up emmc phy analog blocks */
ret = rockchip_emmc_phy_power(rk_phy, PHYCTRL_PDB_PWR_ON);
if (ret)
--
2.8.0.rc3.226.g39d4020
\
 
 \ /
  Last update: 2016-05-13 01:01    [W:0.277 / U:0.044 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site