lkml.org 
[lkml]   [2016]   [Apr]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH V11 3/6] pinctrl: add DT binding doc for pincontrol of PMIC max77620/max20024
Date
Maxim Semiconductor's PMIC MAX77620/MAX20024 has 8 GPIO pins
which act as GPIO as well as special function mode.

Add DT binding document to configure pins in function mode as
well as pin configuration parameters.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

---
Changes from V4:
- Separate out from pincontrol driver

Changes from V5:
- Starting patch title with pinctrl instead of DT:pinctrl

Changes from V6/V7:
- None

Changes on V8:
- Collected Ack from Linus.

Changes from V9/10:
None

.../bindings/pinctrl/pinctrl-max77620.txt | 127 +++++++++++++++++++++
1 file changed, 127 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt

diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt
new file mode 100644
index 0000000..ad4fce3
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt
@@ -0,0 +1,127 @@
+Pincontrol driver for MAX77620 Power management IC from Maxim Semiconductor.
+
+Device has 8 GPIO pins which can be configured as GPIO as well as the
+special IO functions.
+
+Please refer file <devicetree/bindings/pinctrl/pinctrl-bindings.txt>
+for details of the common pinctrl bindings used by client devices,
+including the meaning of the phrase "pin configuration node".
+
+Optional Pinmux properties:
+--------------------------
+Following properties are required if default setting of pins are required
+at boot.
+- pinctrl-names: A pinctrl state named per <pinctrl-binding.txt>.
+- pinctrl[0...n]: Properties to contain the phandle for pinctrl states per
+ <pinctrl-binding.txt>.
+
+The pin configurations are defined as child of the pinctrl states node. Each
+sub-node have following properties:
+
+Required properties:
+------------------
+- pins: List of pins. Valid values of pins properties are:
+ gpio0, gpio1, gpio2, gpio3, gpio4, gpio5, gpio6, gpio7.
+
+Optional properties:
+-------------------
+Following are optional properties defined as pinmux DT binding document
+<pinctrl-bindings.txt>. Absence of properties will leave the configuration
+on default.
+ function,
+ drive-push-pull,
+ drive-open-drain,
+ bias-pull-up,
+ bias-pull-down.
+
+Valid values for function properties are:
+ gpio, lpm-control-in, fps-out, 32k-out, sd0-dvs-in, sd1-dvs-in,
+ reference-out
+
+Theres is also customised properties for the GPIO1, GPIO2 and GPIO3. These
+customised properties are required to configure FPS configuration parameters
+of these GPIOs. Please refer <devicetree/bindings/mfd/max77620.txt> for more
+detail of Flexible Power Sequence (FPS).
+
+- maxim,active-fps-source: FPS source for the GPIOs to get
+ enabled/disabled when system is in
+ active state. Valid values are:
+ - MAX77620_FPS_SRC_0,
+ FPS source is FPS0.
+ - MAX77620_FPS_SRC_1,
+ FPS source is FPS1
+ - MAX77620_FPS_SRC_2 and
+ FPS source is FPS2
+ - MAX77620_FPS_SRC_NONE.
+ GPIO is not controlled
+ by FPS events and it gets
+ enabled/disabled by register
+ access.
+ Absence of this property will leave
+ the FPS configuration register for that
+ GPIO to default configuration.
+
+- maxim,active-fps-power-up-slot: Sequencing event slot number on which
+ the GPIO get enabled when
+ master FPS input event set to HIGH.
+ Valid values are 0 to 7.
+ This is applicable if FPS source is
+ selected as FPS0, FPS1 or FPS2.
+
+- maxim,active-fps-power-down-slot: Sequencing event slot number on which
+ the GPIO get disabled when master
+ FPS input event set to LOW.
+ Valid values are 0 to 7.
+ This is applicable if FPS source is
+ selected as FPS0, FPS1 or FPS2.
+
+- maxim,suspend-fps-source: This is same as property
+ "maxim,active-fps-source" but value
+ get configured when system enters in
+ to suspend state.
+
+- maxim,suspend-fps-power-up-slot: This is same as property
+ "maxim,active-fps-power-up-slot" but
+ this value get configured into FPS
+ configuration register when system
+ enters into suspend.
+ This is applicable if suspend state
+ FPS source is selected as FPS0, FPS1 or
+
+- maxim,suspend-fps-power-down-slot: This is same as property
+ "maxim,active-fps-power-down-slot" but
+ this value get configured into FPS
+ configuration register when system
+ enters into suspend.
+ This is applicable if suspend state
+ FPS source is selected as FPS0, FPS1 or
+ FPS2.
+
+Example:
+--------
+#include <dt-bindings/mfd/max77620.h>
+...
+max77620@3c {
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&spmic_default>;
+
+ spmic_default: pinmux@0 {
+ pin_gpio0 {
+ pins = "gpio0";
+ function = "gpio";
+ };
+
+ pin_gpio1 {
+ pins = "gpio1";
+ function = "fps-out";
+ maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+ };
+
+ pin_gpio2 {
+ pins = "gpio2";
+ function = "fps-out";
+ maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
+ };
+ };
+};
--
2.1.4
\
 
 \ /
  Last update: 2016-04-28 12:21    [W:0.103 / U:3.256 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site