lkml.org 
[lkml]   [2016]   [Apr]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/2] arm64: mem-model: add flatmem model for arm64
Hi Chen,

On Wed, Apr 20, 2016 at 11:18:54AM +0800, Chen Feng wrote:
> Thanks for your reply.
> On 2016/4/12 22:59, Catalin Marinas wrote:
> > On Mon, Apr 11, 2016 at 12:31:53PM +0200, Ard Biesheuvel wrote:
> >> On 11 April 2016 at 11:59, Chen Feng <puck.chen@hisilicon.com> wrote:
> >>> On 2016/4/11 16:00, Ard Biesheuvel wrote:
> >>>> On 11 April 2016 at 09:55, Chen Feng <puck.chen@hisilicon.com> wrote:
> >>>>> On 2016/4/11 15:35, Ard Biesheuvel wrote:
> >>>>>> On 11 April 2016 at 04:49, Chen Feng <puck.chen@hisilicon.com> wrote:
> >>>>>>> 0 1.5G 2G 3.5G 4G
> >>>>>>> | | | | |
> >>>>>>> +--------------+------+---------------+--------------+
> >>>>>>> | MEM | hole | MEM | IO (regs) |
> >>>>>>> +--------------+------+---------------+--------------+
> >>>>> The hole in 1.5G ~ 2G is also allocated mem-map array. And also with the 3.5G ~ 4G.
> >>>>
> >>>> No, it is not. It may be covered by a section, but that does not mean
> >>>> sparsemem vmemmap will actually allocate backing for it. The
> >>>> granularity used by sparsemem vmemmap on a 4k pages kernel is 128 MB,
> >>>> due to the fact that the backing is performed at PMD granularity.
> >>>>
> >>>> Please, could you share the contents of the vmemmap section in
> >>>> /sys/kernel/debug/kernel_page_tables of your system running with
> >>>> sparsemem vmemmap enabled? You will need to set CONFIG_ARM64_PTDUMP=y
> >>>
> >>> Please see the pg-tables below.
> >>>
> >>> With sparse and vmemmap enable.
> >>>
> >>> ---[ vmemmap start ]---
> >>> 0xffffffbdc0200000-0xffffffbdc4800000 70M RW NX SHD AF UXN MEM/NORMAL
> >>> ---[ vmemmap end ]---
> > [...]
> >>> The board is 4GB, and the memap is 70MB
> >>> 1G memory --- 14MB mem_map array.
> >>
> >> No, this is incorrect. 1 GB corresponds with 16 MB worth of struct
> >> pages assuming sizeof(struct page) == 64
> >>
> >> So you are losing 6 MB to rounding here, which I agree is significant.
> >> I wonder if it makes sense to use a lower value for SECTION_SIZE_BITS
> >> on 4k pages kernels, but perhaps we're better off asking the opinion
> >> of the other cc'ees.
> >
> > IIRC, SECTION_SIZE_BITS was chosen to be the maximum sane value we were
> > thinking of at the time, assuming that 1GB RAM alignment to be fairly
> > normal. For the !SPARSEMEM_VMEMMAP case, we should probably be fine with
> > 29 but, as Will said, we need to be careful with the page flags. At a
> > quick look, we have 25 page flags, 2 bits per zone, NUMA nodes and (48 -
> > section_size_bits) for the section width. We also need to take into
> > account 4 more bits for 52-bit PA support (ARMv8.2). So, without NUMA
> > nodes, we are currently at 49 bits used in page->flags.
> >
> > For the SPARSEMEM_VMEMMAP case, we can decrease the SECTION_SIZE_BITS in
> > the MAX_ORDER limit.
> >
> > An alternative would be to free the vmemmap holes later (but still keep
> > the vmemmap mapping alias). Yet another option would be to change the
> > sparse_mem_map_populate() logic get the actual section end rather than
> > always assuming PAGES_PER_SECTION. But I don't think any of these are
> > worth if we can safely reduce SECTION_SIZE_BITS.
>
> Yes,
> currently,it's safely to reduce the SECTION_SIZE_BITS to match this issue
> very well.
>
> As I mentioned before, if the memory layout is not like this scene. There
> will be not suitable to reduce the SECTION_SIZE_BITS.

SECTION_SIZE_BITS is not meant to cover all possible combinations but
only sane ones and it was primarily targeted at the ARM memory map
recommendations:

http://infocenter.arm.com/help/topic/com.arm.doc.den0001c/DEN0001C_principles_of_arm_memory_maps.pdf

As you know have reported a platform that uses half GB-aligned RAM
blocks/sizes, I'm fine to change SECTION_SIZE_BITS. If in the future we
see even more insane configurations and the memory wasted is
significant, we may have to revisit this (I also proposed an alternative
above like freeing the vmmemap holes, that's not too different from a
flat memmap array).

> We have 4G memory, and 64GB phys address.
>
> There will be a lot of holes in the memory layout.
> And the *holes size are not always the same*.

It's not the hole size that matters but rather the section size and
alignment.

> So,it's the reason I want to enable flat-mem in ARM64-ARCH. Why not makes
> the flat-mem an optional setting for arm64?

Because (a) I strongly believe in single Image, (b) I do not want to
increase the configuration space unnecessarily (already large enough
with all the page and VA size combinations) and (c) I don't see any
advantage in flatmem compared to sparsemem+vmemap.

--
Catalin

\
 
 \ /
  Last update: 2016-04-20 11:41    [W:0.057 / U:0.576 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site