lkml.org 
[lkml]   [2016]   [Mar]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 6/6] cpufreq: schedutil: New governor based on scheduler utilization data
On 2 March 2016 at 23:49, Rafael J. Wysocki <rafael@kernel.org> wrote:
> On Wed, Mar 2, 2016 at 6:58 PM, Rafael J. Wysocki <rafael@kernel.org> wrote:
>> On Wed, Mar 2, 2016 at 6:10 PM, Vincent Guittot
>> <vincent.guittot@linaro.org> wrote:
>>> Hi Rafael,
>>>
>>>
>>> On 2 March 2016 at 03:27, Rafael J. Wysocki <rjw@rjwysocki.net> wrote:
>>>> From: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
>>>>
>>>> Add a new cpufreq scaling governor, called "schedutil", that uses
>>>> scheduler-provided CPU utilization information as input for making
>>>> its decisions.
>>>>
>>>> Doing that is possible after commit fe7034338ba0 (cpufreq: Add
>>>> mechanism for registering utilization update callbacks) that
>>>> introduced cpufreq_update_util() called by the scheduler on
>>>> utilization changes (from CFS) and RT/DL task status updates.
>>>> In particular, CPU frequency scaling decisions may be based on
>>>> the the utilization data passed to cpufreq_update_util() by CFS.
>>>>
>>>> The new governor is relatively simple.
>>>>
>>>> The frequency selection formula used by it is essentially the same
>>>> as the one used by the "ondemand" governor, although it doesn't use
>>>> the additional up_threshold parameter, but instead of computing the
>>>> load as the "non-idle CPU time" to "total CPU time" ratio, it takes
>>>> the utilization data provided by CFS as input. More specifically,
>>>> it represents "load" as the util/max ratio, where util and max
>>>> are the utilization and CPU capacity coming from CFS.
>>>>
>>>
>>> [snip]
>>>
>>>> +
>>>> +static void sugov_update_commit(struct sugov_policy *sg_policy, u64 time,
>>>> + unsigned long util, unsigned long max,
>>>> + unsigned int next_freq)
>>>> +{
>>>> + struct cpufreq_policy *policy = sg_policy->policy;
>>>> + unsigned int rel;
>>>> +
>>>> + if (next_freq > policy->max)
>>>> + next_freq = policy->max;
>>>> + else if (next_freq < policy->min)
>>>> + next_freq = policy->min;
>>>> +
>>>> + sg_policy->last_freq_update_time = time;
>>>> + if (sg_policy->next_freq == next_freq)
>>>> + return;
>>>> +
>>>> + sg_policy->next_freq = next_freq;
>>>> + /*
>>>> + * If utilization is less than max / 4, use RELATION_C to allow the
>>>> + * minimum frequency to be selected more often in case the distance from
>>>> + * it to the next available frequency in the table is significant.
>>>> + */
>>>> + rel = util < (max >> 2) ? CPUFREQ_RELATION_C : CPUFREQ_RELATION_L;
>>>> + if (policy->fast_switch_possible) {
>>>> + cpufreq_driver_fast_switch(policy, next_freq, rel);
>>>> + } else {
>>>> + sg_policy->relation = rel;
>>>> + sg_policy->work_in_progress = true;
>>>> + irq_work_queue(&sg_policy->irq_work);
>>>> + }
>>>> +}
>>>> +
>>>> +static void sugov_update_single(struct update_util_data *data, u64 time,
>>>> + unsigned long util, unsigned long max)
>>>> +{
>>>> + struct sugov_cpu *sg_cpu = container_of(data, struct sugov_cpu, update_util);
>>>> + struct sugov_policy *sg_policy = sg_cpu->sg_policy;
>>>> + unsigned int min_f, max_f, next_f;
>>>> +
>>>> + if (!sugov_should_update_freq(sg_policy, time))
>>>> + return;
>>>> +
>>>> + min_f = sg_policy->policy->cpuinfo.min_freq;
>>>> + max_f = sg_policy->policy->cpuinfo.max_freq;
>>>> + next_f = util > max ? max_f : min_f + util * (max_f - min_f) / max;
>>>
>>> I think it has been pointed out in another email's thread but you
>>> should change the way the next_f is computed. util reflects the
>>> utilization of a CPU from 0 to its max compute capacity whereas
>>> ondemand was using the load at the current frequency during the last
>>> time window. I have understood that you want to keep same formula than
>>> ondemand as a starting point but you use a different input to
>>> calculate the next frequency so i don't see the rational of keeping
>>> this formula.
>>
>> It is a formula that causes the entire available frequency range to be
>> utilized proportionally to the utilization as reported by the
>> scheduler (modulo the policy->min/max limits). Its (significant IMO)
>> advantage is that it doesn't require any additional factors that would
>> need to be determined somehow.
>
> In case a more formal derivation of this formula is needed, it is
> based on the following 3 assumptions:
>
> (1) Performance is a linear function of frequency.
> (2) Required performance is a linear function of the utilization ratio
> x = util/max as provided by the scheduler (0 <= x <= 1).

Just to mention that the utilization that you are using, varies with
the frequency which add another variable in your equation

> (3) The minimum possible frequency (min_freq) corresponds to x = 0 and
> the maximum possible frequency (max_freq) corresponds to x = 1.
>
> (1) and (2) combined imply that
>
> f = a * x + b
>
> (f - frequency, a, b - constants to be determined) and then (3) quite
> trivially leads to b = min_freq and a = max_freq - min_freq.
>
> Now, of course, the linearity assumptions may be questioned, but then
> it's just the first approximation. If you go any further, though, you
> end up with an expansion series like this:
>
> f(x) = c_0 + c_1 * x + c_2 * x^2 + c_3 * x^3 + ...
>
> where all of the c_j need to be determined in principle. With luck,
> if you can guess what kind of a function f(x) may be, it may be
> possible to reduce the number of coefficients to determine, but
> question is whether or not that is going to work universally for all
> systems.
>
> Thanks,
> Rafael

\
 
 \ /
  Last update: 2016-03-03 15:41    [W:0.171 / U:0.088 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site