lkml.org 
[lkml]   [2016]   [Mar]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 11/12] ARM: dts: dragonboard-600c: add i2c support
From
Date


On 29/03/16 15:44, Bjorn Andersson wrote:
> On Wed 23 Mar 12:48 PDT 2016, Srinivas Kandagatla wrote:
>
>> This patch adds nodes required to enable 4 i2c buses on the board which
>> are connected to various sensors and eeprom.
>>
>
> I would like for the pinconf for these blocks to be in this patch (and
> file) to make it clear how they are configured and where to change them.
>
When I started adding this I had same opinion, I will do that in next
release.

thanks,
srini
> Regards,
> Bjorn
>
>> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
>> ---
>> .../arm/boot/dts/qcom-apq8064-dragonboard-600c.dts | 46 ++++++++++++++++++++++
>> 1 file changed, 46 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/qcom-apq8064-dragonboard-600c.dts b/arch/arm/boot/dts/qcom-apq8064-dragonboard-600c.dts
>> index 4fecd94..942de04 100644
>> --- a/arch/arm/boot/dts/qcom-apq8064-dragonboard-600c.dts
>> +++ b/arch/arm/boot/dts/qcom-apq8064-dragonboard-600c.dts
>> @@ -8,6 +8,10 @@
>> aliases {
>> serial0 = &gsbi7_serial;
>> serial1 = &gsbi1_serial;
>> + i2c0 = &gsbi2_i2c;
>> + i2c1 = &gsbi3_i2c;
>> + i2c2 = &gsbi4_i2c;
>> + i2c3 = &gsbi7_i2c;
>> };
>>
>> regulators {
>> @@ -180,6 +184,42 @@
>> };
>> };
>>
>> + gsbi@12480000 {
>> + status = "okay";
>> + qcom,mode = <GSBI_PROT_I2C>;
>> + i2c@124a0000 {
>> + /* On Low speed expansion and Sensors */
>> + label = "LS-I2C0";
>> + status = "okay";
>> + };
>> + };
>> +
>> + gsbi@16200000 {
>> + status = "okay";
>> + qcom,mode = <GSBI_PROT_I2C>;
>> + i2c@16280000 {
>> + /* On Low speed expansion */
>> + status = "okay";
>> + label = "LS-I2C1";
>> + clock-frequency = <200000>;
>> + eeprom@52 {
>> + compatible = "atmel,24c128";
>> + reg = <0x52>;
>> + pagesize = <64>;
>> + };
>> + };
>> + };
>> +
>> + gsbi@16300000 {
>> + status = "okay";
>> + qcom,mode = <GSBI_PROT_I2C>;
>> + i2c@16380000 {
>> + /* On High speed expansion */
>> + label = "HS-CAM-I2C3";
>> + status = "okay";
>> + };
>> + };
>> +
>> /* DEBUG UART */
>> gsbi@16600000 {
>> status = "okay";
>> @@ -190,6 +230,12 @@
>> pinctrl-names = "default";
>> pinctrl-0 = <&gsbi7_uart_2pins>;
>> };
>> +
>> + i2c@16680000 {
>> + /* On High speed expansion */
>> + status = "okay";
>> + label = "HS-CAM-I2C2";
>> + };
>> };
>>
>> leds {
>> --
>> 2.5.0
>>

\
 
 \ /
  Last update: 2016-03-29 17:21    [W:0.084 / U:0.264 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site