lkml.org 
[lkml]   [2016]   [Mar]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 11/12] ARM: dts: dragonboard-600c: add i2c support
On Wed 23 Mar 12:48 PDT 2016, Srinivas Kandagatla wrote:

> This patch adds nodes required to enable 4 i2c buses on the board which
> are connected to various sensors and eeprom.
>

I would like for the pinconf for these blocks to be in this patch (and
file) to make it clear how they are configured and where to change them.

Regards,
Bjorn

> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
> ---
> .../arm/boot/dts/qcom-apq8064-dragonboard-600c.dts | 46 ++++++++++++++++++++++
> 1 file changed, 46 insertions(+)
>
> diff --git a/arch/arm/boot/dts/qcom-apq8064-dragonboard-600c.dts b/arch/arm/boot/dts/qcom-apq8064-dragonboard-600c.dts
> index 4fecd94..942de04 100644
> --- a/arch/arm/boot/dts/qcom-apq8064-dragonboard-600c.dts
> +++ b/arch/arm/boot/dts/qcom-apq8064-dragonboard-600c.dts
> @@ -8,6 +8,10 @@
> aliases {
> serial0 = &gsbi7_serial;
> serial1 = &gsbi1_serial;
> + i2c0 = &gsbi2_i2c;
> + i2c1 = &gsbi3_i2c;
> + i2c2 = &gsbi4_i2c;
> + i2c3 = &gsbi7_i2c;
> };
>
> regulators {
> @@ -180,6 +184,42 @@
> };
> };
>
> + gsbi@12480000 {
> + status = "okay";
> + qcom,mode = <GSBI_PROT_I2C>;
> + i2c@124a0000 {
> + /* On Low speed expansion and Sensors */
> + label = "LS-I2C0";
> + status = "okay";
> + };
> + };
> +
> + gsbi@16200000 {
> + status = "okay";
> + qcom,mode = <GSBI_PROT_I2C>;
> + i2c@16280000 {
> + /* On Low speed expansion */
> + status = "okay";
> + label = "LS-I2C1";
> + clock-frequency = <200000>;
> + eeprom@52 {
> + compatible = "atmel,24c128";
> + reg = <0x52>;
> + pagesize = <64>;
> + };
> + };
> + };
> +
> + gsbi@16300000 {
> + status = "okay";
> + qcom,mode = <GSBI_PROT_I2C>;
> + i2c@16380000 {
> + /* On High speed expansion */
> + label = "HS-CAM-I2C3";
> + status = "okay";
> + };
> + };
> +
> /* DEBUG UART */
> gsbi@16600000 {
> status = "okay";
> @@ -190,6 +230,12 @@
> pinctrl-names = "default";
> pinctrl-0 = <&gsbi7_uart_2pins>;
> };
> +
> + i2c@16680000 {
> + /* On High speed expansion */
> + status = "okay";
> + label = "HS-CAM-I2C2";
> + };
> };
>
> leds {
> --
> 2.5.0
>

\
 
 \ /
  Last update: 2016-03-29 17:01    [W:0.267 / U:1.000 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site