lkml.org 
[lkml]   [2016]   [Mar]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH 2/4 v3] drm: Add DT bindings documentation for ARC PGU display controller
Date
Hi Rob,

On Mon, 2016-03-21 at 08:04 -0500, Rob Herring wrote:
> On Fri, Mar 11, 2016 at 06:42:37PM +0300, Alexey Brodkin wrote:
> >
> > This add DT bindings documentation for ARC PGU display controller.
> >
> > Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
> > Cc: Rob Herring <robh+dt@kernel.org>
> > Cc: Pawel Moll <pawel.moll@arm.com>
> > Cc: Mark Rutland <mark.rutland@arm.com>
> > Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
> > Cc: Kumar Gala <galak@codeaurora.org>
> > Cc: David Airlie <airlied@linux.ie>
> > Cc: dri-devel@lists.freedesktop.org
> > Cc: devicetree@vger.kernel.org
> > Cc: linux-snps-arc@lists.infradead.org
> > ---
> >
> > Changes v2 -> v3:
> >  * Reverted back to initial larger version of example
> >    with minor fixes (thanks Rob for spotting those).
> >
> > Changes v1 -> v2:
> >  * Removed everything except PGU node itself.
> >
> >  .../devicetree/bindings/display/snps,arcpgu.txt    | 72 ++++++++++++++++++++++
> >  1 file changed, 72 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/display/snps,arcpgu.txt
> >
> > diff --git a/Documentation/devicetree/bindings/display/snps,arcpgu.txt
> > b/Documentation/devicetree/bindings/display/snps,arcpgu.txt
> > new file mode 100644
> > index 0000000..b130924
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/snps,arcpgu.txt
> > @@ -0,0 +1,72 @@
> > +ARC PGU
> > +
> > +This is a display controller found on several development boards produced
> > +by Synopsys. The ARC PGU is an RGB streamer that reads the data from a
> > +framebuffer and sends it to a single digital encoder (usually HDMI).
> > +
> > +Required properties:
> > +  - compatible: "snps,arcpgu"
> > +  - reg: Physical base address and length of the controller's registers.
> > +  - clocks: A list of phandle + clock-specifier pairs, one for each
> > +    entry in 'clock-names'.
> > +  - clock-names: A list of clock names. For ARC PGU it should contain:
> > +      - "pxlclk" for the clock feeding the output PLL of the controller.
> > +  - encoder-slave: Phandle of encoder chip.
> Drop this as discussed.

Ok I'll do that.
But what about my example below?
Do I need to remove encoder node from it as well?

> >
> > +
> > +Required sub-nodes:
> > +  - port: The PGU connection to an encoder chip.
> > +
> > +Example:
> > +
> > +/ {
> > + ...
> > +
> > + pgu@XXXXXXXX {
> > + compatible = "snps,arcpgu";
> > + reg = <0xXXXXXXXX 0x400>;
> > + clocks = <&clock_node>;
> > + clock-names = "pxlclk";
> > + encoder-slave = <&encoder_node>;
> > +
> > + port {
> > + pgu_output: endpoint {
> > + remote-endpoint = <&hdmi_enc_input>;
> > + };
> > + };
> > + };
> > +
> > + /* HDMI encoder on I2C bus */
> > + i2c@XXXXXXXX {
> > + compatible = "...";
> > +
> > + encoder_node:encoder_node@0xXX{
> Don't use underscores in node names. Just "hdmi@xx"

Ok still I may keep label "encoder_node" here, right?

-Alexey

\
 
 \ /
  Last update: 2016-03-24 16:41    [W:0.108 / U:0.232 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site