lkml.org 
[lkml]   [2016]   [Mar]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 04/15] irqchip/gic: WARN if setting the interrupt type fails
From
Date

On 18/03/16 09:20, Geert Uytterhoeven wrote:
> On Thu, Mar 17, 2016 at 5:20 PM, Jon Hunter <jonathanh@nvidia.com> wrote:
>> On 17/03/16 15:18, Jason Cooper wrote:
>>> On Thu, Mar 17, 2016 at 03:04:01PM +0000, Jon Hunter wrote:
>>>> On 17/03/16 14:51, Thomas Gleixner wrote:
>>>>> On Thu, 17 Mar 2016, Jon Hunter wrote:
>>>>>> Setting the interrupt type for private peripheral interrupts (PPIs) may
>>>>>> not be supported by a given GIC because it is IMPLEMENTATION DEFINED
>>>>>> whether this is allowed. There is no way to know if setting the type is
>>>>>> supported for a given GIC and so the value written is read back to
>>>>>> verify it matches the desired configuration. If it does not match then
>>>>>> an error is return.
>>>>>>
>>>>>> There are cases where the interrupt configuration read from firmware
>>>>>> (such as a device-tree blob), has been incorrect and hence
>>>>>> gic_configure_irq() has returned an error. This error has gone
>>>>>> undetected because the error code returned was ignored but the interrupt
>>>>>> still worked fine because the configuration for the interrupt could not
>>>>>> be overwritten.
>>>>>>
>>>>>> Given that this has done undetected and we should only fail to set the
>>>>>> type for PPIs whose configuration cannot be changed anyway, don't return
>>>>>> an error and simply WARN if this fails. This will allows us to fix up any
>>>>>> places in the kernel where we should be checking the return status and
>>>>>> maintain back compatibility with firmware images that may have incorrect
>>>>>> interrupt configurations.
>>>>>
>>>>> Though silently returning 0 is really the wrong thing to do. You can add the
>>>>> warn, but why do you want to return success?
>>>>
>>>> Yes that would be the correct thing to do I agree. However, the problem
>>>> is that if we do this, then after the patch "irqdomain: Don't set type
>>>> when mapping an IRQ" is applied, we may break interrupts for some
>>>> existing device-tree binaries that have bad configuration (such as omap4
>>>> and tegra20/30 ... see patches 1 and 2) that have gone unnoticed. So it
>>>> is a back compatibility issue.
>
> Indeed (also for sh73a0 and r8a7779).

Thanks. I was wondering if there are others. Do you know what the
correct setting should be? Ie. should it be IRQ_TYPE_EDGE_RISING as
well? I can then include this with OMAP and Tegra.

>>> This sounds like a textbook case for adding a boolean dt property. If
>>> "can-set-ppi-type" is absent (old DT blobs and new blobs without the
>>> ability), warn and return zero. If it's present, the driver can set the
>>> type, returning errors as encountered.
>>
>> True. However, if we did have this "can-set-ppi-type" property set for a
>> device, it really should never fail (unless someone specified it
>> incorrectly). So I am trying to understand the value in adding a new DT
>> property.
>
> Do we really want to add properties that basically indicate that a description
> in DT is correct?
>
> Alternatively, it can be fixed in the kernel in a DT quirk (if SoC == xxx then
> fix TWD).

I am not sure I fully understand your proposal, but please note that it
may not be just limited to the TWD (although this does appear to be the
one client that is wrong for a lot of SoCs). PPIs are also used for the
armv7/8 timers as well.

The problem is that we have a lot of SoCs with twd-timers and I have no
way to test all of these to know which could be a problem. So I thought
that warning would be a good first step to fixing them.

However, I am still trying to see the real value in returning an error
in this case. May be I am the only one with that perspective?

Cheers
Jon

\
 
 \ /
  Last update: 2016-03-18 11:21    [W:0.105 / U:2.416 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site