lkml.org 
[lkml]   [2016]   [Feb]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[RFC PATCH 14/19] ide: remove deprecated serverworks host driver
Date
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively.

The replacement driver (pata_serverworks) has been available
since 2006 and it supports all the hardware supported by the old
serverworks host driver.

Remove the deprecated serverworks host driver.

Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
---
drivers/ide/Kconfig | 7 -
drivers/ide/Makefile | 1 -
drivers/ide/serverworks.c | 449 ----------------------------------------------
3 files changed, 457 deletions(-)
delete mode 100644 drivers/ide/serverworks.c

diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index e4794af..1379ce6 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -428,13 +428,6 @@ config BLK_DEV_PDC202XX_NEW
tristate "PROMISE PDC202{68|69|70|71|75|76|77} support"
select BLK_DEV_IDEDMA_PCI

-config BLK_DEV_SVWKS
- tristate "ServerWorks OSB4/CSB5/CSB6 chipsets support"
- select BLK_DEV_IDEDMA_PCI
- help
- This driver adds PIO/(U)DMA support for the ServerWorks OSB4/CSB5
- chipsets.
-
config BLK_DEV_SGIIOC4
tristate "Silicon Graphics IOC4 chipset ATA/ATAPI support"
depends on (IA64_SGI_SN2 || IA64_GENERIC) && SGI_IOC4
diff --git a/drivers/ide/Makefile b/drivers/ide/Makefile
index de19568..9fe5f5f 100644
--- a/drivers/ide/Makefile
+++ b/drivers/ide/Makefile
@@ -44,7 +44,6 @@ obj-$(CONFIG_BLK_DEV_IT8172) += it8172.o
obj-$(CONFIG_BLK_DEV_NS87415) += ns87415.o
obj-$(CONFIG_BLK_DEV_PDC202XX_NEW) += pdc202xx_new.o
obj-$(CONFIG_BLK_DEV_PIIX) += piix.o
-obj-$(CONFIG_BLK_DEV_SVWKS) += serverworks.o
obj-$(CONFIG_BLK_DEV_SGIIOC4) += sgiioc4.o
obj-$(CONFIG_BLK_DEV_SIIMAGE) += siimage.o
obj-$(CONFIG_BLK_DEV_SIS5513) += sis5513.o
diff --git a/drivers/ide/serverworks.c b/drivers/ide/serverworks.c
deleted file mode 100644
index a97affc..0000000
--- a/drivers/ide/serverworks.c
+++ /dev/null
@@ -1,449 +0,0 @@
-/*
- * Copyright (C) 1998-2000 Michel Aubry
- * Copyright (C) 1998-2000 Andrzej Krzysztofowicz
- * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
- * Copyright (C) 2007-2010 Bartlomiej Zolnierkiewicz
- * Portions copyright (c) 2001 Sun Microsystems
- *
- *
- * RCC/ServerWorks IDE driver for Linux
- *
- * OSB4: `Open South Bridge' IDE Interface (fn 1)
- * supports UDMA mode 2 (33 MB/s)
- *
- * CSB5: `Champion South Bridge' IDE Interface (fn 1)
- * all revisions support UDMA mode 4 (66 MB/s)
- * revision A2.0 and up support UDMA mode 5 (100 MB/s)
- *
- * *** The CSB5 does not provide ANY register ***
- * *** to detect 80-conductor cable presence. ***
- *
- * CSB6: `Champion South Bridge' IDE Interface (optional: third channel)
- *
- * HT1000: AKA BCM5785 - Hypertransport Southbridge for Opteron systems. IDE
- * controller same as the CSB6. Single channel ATA100 only.
- *
- * Documentation:
- * Available under NDA only. Errata info very hard to get.
- *
- */
-
-#include <linux/types.h>
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/ide.h>
-#include <linux/init.h>
-
-#include <asm/io.h>
-
-#define DRV_NAME "serverworks"
-
-#define SVWKS_CSB5_REVISION_NEW 0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */
-#define SVWKS_CSB6_REVISION 0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */
-
-/* Seagate Barracuda ATA IV Family drives in UDMA mode 5
- * can overrun their FIFOs when used with the CSB5 */
-static const char *svwks_bad_ata100[] = {
- "ST320011A",
- "ST340016A",
- "ST360021A",
- "ST380021A",
- NULL
-};
-
-static int check_in_drive_lists (ide_drive_t *drive, const char **list)
-{
- char *m = (char *)&drive->id[ATA_ID_PROD];
-
- while (*list)
- if (!strcmp(*list++, m))
- return 1;
- return 0;
-}
-
-static u8 svwks_udma_filter(ide_drive_t *drive)
-{
- struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
-
- if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE) {
- return 0x1f;
- } else if (dev->revision < SVWKS_CSB5_REVISION_NEW) {
- return 0x07;
- } else {
- u8 btr = 0, mode, mask;
-
- pci_read_config_byte(dev, 0x5A, &btr);
- mode = btr & 0x3;
-
- /* If someone decides to do UDMA133 on CSB5 the same
- issue will bite so be inclusive */
- if (mode > 2 && check_in_drive_lists(drive, svwks_bad_ata100))
- mode = 2;
-
- switch(mode) {
- case 3: mask = 0x3f; break;
- case 2: mask = 0x1f; break;
- case 1: mask = 0x07; break;
- default: mask = 0x00; break;
- }
-
- return mask;
- }
-}
-
-static u8 svwks_csb_check (struct pci_dev *dev)
-{
- switch (dev->device) {
- case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
- case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
- case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
- case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE:
- return 1;
- default:
- break;
- }
- return 0;
-}
-
-static void svwks_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- static const u8 pio_modes[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
- static const u8 drive_pci[] = { 0x41, 0x40, 0x43, 0x42 };
-
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- const u8 pio = drive->pio_mode - XFER_PIO_0;
-
- pci_write_config_byte(dev, drive_pci[drive->dn], pio_modes[pio]);
-
- if (svwks_csb_check(dev)) {
- u16 csb_pio = 0;
-
- pci_read_config_word(dev, 0x4a, &csb_pio);
-
- csb_pio &= ~(0x0f << (4 * drive->dn));
- csb_pio |= (pio << (4 * drive->dn));
-
- pci_write_config_word(dev, 0x4a, csb_pio);
- }
-}
-
-static void svwks_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- static const u8 udma_modes[] = { 0x00, 0x01, 0x02, 0x03, 0x04, 0x05 };
- static const u8 dma_modes[] = { 0x77, 0x21, 0x20 };
- static const u8 drive_pci2[] = { 0x45, 0x44, 0x47, 0x46 };
-
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- const u8 speed = drive->dma_mode;
- u8 unit = drive->dn & 1;
-
- u8 ultra_enable = 0, ultra_timing = 0, dma_timing = 0;
-
- pci_read_config_byte(dev, (0x56|hwif->channel), &ultra_timing);
- pci_read_config_byte(dev, 0x54, &ultra_enable);
-
- ultra_timing &= ~(0x0F << (4*unit));
- ultra_enable &= ~(0x01 << drive->dn);
-
- if (speed >= XFER_UDMA_0) {
- dma_timing |= dma_modes[2];
- ultra_timing |= (udma_modes[speed - XFER_UDMA_0] << (4 * unit));
- ultra_enable |= (0x01 << drive->dn);
- } else if (speed >= XFER_MW_DMA_0)
- dma_timing |= dma_modes[speed - XFER_MW_DMA_0];
-
- pci_write_config_byte(dev, drive_pci2[drive->dn], dma_timing);
- pci_write_config_byte(dev, (0x56|hwif->channel), ultra_timing);
- pci_write_config_byte(dev, 0x54, ultra_enable);
-}
-
-static int init_chipset_svwks(struct pci_dev *dev)
-{
- unsigned int reg;
- u8 btr;
-
- /* force Master Latency Timer value to 64 PCICLKs */
- pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x40);
-
- /* OSB4 : South Bridge and IDE */
- if (dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
- struct pci_dev *isa_dev =
- pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
- PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL);
- if (isa_dev) {
- pci_read_config_dword(isa_dev, 0x64, &reg);
- reg &= ~0x00002000; /* disable 600ns interrupt mask */
- if(!(reg & 0x00004000))
- printk(KERN_DEBUG DRV_NAME " %s: UDMA not BIOS "
- "enabled.\n", pci_name(dev));
- reg |= 0x00004000; /* enable UDMA/33 support */
- pci_write_config_dword(isa_dev, 0x64, reg);
- pci_dev_put(isa_dev);
- }
- }
-
- /* setup CSB5/CSB6 : South Bridge and IDE option RAID */
- else if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) ||
- (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
- (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) {
-
- /* Third Channel Test */
- if (!(PCI_FUNC(dev->devfn) & 1)) {
- struct pci_dev * findev = NULL;
- u32 reg4c = 0;
- findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
- PCI_DEVICE_ID_SERVERWORKS_CSB5, NULL);
- if (findev) {
- pci_read_config_dword(findev, 0x4C, &reg4c);
- reg4c &= ~0x000007FF;
- reg4c |= 0x00000040;
- reg4c |= 0x00000020;
- pci_write_config_dword(findev, 0x4C, reg4c);
- pci_dev_put(findev);
- }
- outb_p(0x06, 0x0c00);
- dev->irq = inb_p(0x0c01);
- } else {
- struct pci_dev * findev = NULL;
- u8 reg41 = 0;
-
- findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
- PCI_DEVICE_ID_SERVERWORKS_CSB6, NULL);
- if (findev) {
- pci_read_config_byte(findev, 0x41, &reg41);
- reg41 &= ~0x40;
- pci_write_config_byte(findev, 0x41, reg41);
- pci_dev_put(findev);
- }
- /*
- * This is a device pin issue on CSB6.
- * Since there will be a future raid mode,
- * early versions of the chipset require the
- * interrupt pin to be set, and it is a compatibility
- * mode issue.
- */
- if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE)
- dev->irq = 0;
- }
-// pci_read_config_dword(dev, 0x40, &pioreg)
-// pci_write_config_dword(dev, 0x40, 0x99999999);
-// pci_read_config_dword(dev, 0x44, &dmareg);
-// pci_write_config_dword(dev, 0x44, 0xFFFFFFFF);
- /* setup the UDMA Control register
- *
- * 1. clear bit 6 to enable DMA
- * 2. enable DMA modes with bits 0-1
- * 00 : legacy
- * 01 : udma2
- * 10 : udma2/udma4
- * 11 : udma2/udma4/udma5
- */
- pci_read_config_byte(dev, 0x5A, &btr);
- btr &= ~0x40;
- if (!(PCI_FUNC(dev->devfn) & 1))
- btr |= 0x2;
- else
- btr |= (dev->revision >= SVWKS_CSB5_REVISION_NEW) ? 0x3 : 0x2;
- pci_write_config_byte(dev, 0x5A, btr);
- }
- /* Setup HT1000 SouthBridge Controller - Single Channel Only */
- else if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE) {
- pci_read_config_byte(dev, 0x5A, &btr);
- btr &= ~0x40;
- btr |= 0x3;
- pci_write_config_byte(dev, 0x5A, btr);
- }
-
- return 0;
-}
-
-static u8 ata66_svwks_svwks(ide_hwif_t *hwif)
-{
- return ATA_CBL_PATA80;
-}
-
-/* On Dell PowerEdge servers with a CSB5/CSB6, the top two bits
- * of the subsystem device ID indicate presence of an 80-pin cable.
- * Bit 15 clear = secondary IDE channel does not have 80-pin cable.
- * Bit 15 set = secondary IDE channel has 80-pin cable.
- * Bit 14 clear = primary IDE channel does not have 80-pin cable.
- * Bit 14 set = primary IDE channel has 80-pin cable.
- */
-static u8 ata66_svwks_dell(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
-
- if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL &&
- dev->vendor == PCI_VENDOR_ID_SERVERWORKS &&
- (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE ||
- dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE))
- return ((1 << (hwif->channel + 14)) &
- dev->subsystem_device) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
- return ATA_CBL_PATA40;
-}
-
-/* Sun Cobalt Alpine hardware avoids the 80-pin cable
- * detect issue by attaching the drives directly to the board.
- * This check follows the Dell precedent (how scary is that?!)
- *
- * WARNING: this only works on Alpine hardware!
- */
-static u8 ata66_svwks_cobalt(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
-
- if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN &&
- dev->vendor == PCI_VENDOR_ID_SERVERWORKS &&
- dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE)
- return ((1 << (hwif->channel + 14)) &
- dev->subsystem_device) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
- return ATA_CBL_PATA40;
-}
-
-static u8 svwks_cable_detect(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
-
- /* Server Works */
- if (dev->subsystem_vendor == PCI_VENDOR_ID_SERVERWORKS)
- return ata66_svwks_svwks (hwif);
-
- /* Dell PowerEdge */
- if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL)
- return ata66_svwks_dell (hwif);
-
- /* Cobalt Alpine */
- if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN)
- return ata66_svwks_cobalt (hwif);
-
- /* Per Specified Design by OEM, and ASIC Architect */
- if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
- (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2))
- return ATA_CBL_PATA80;
-
- return ATA_CBL_PATA40;
-}
-
-static const struct ide_port_ops osb4_port_ops = {
- .set_pio_mode = svwks_set_pio_mode,
- .set_dma_mode = svwks_set_dma_mode,
-};
-
-static const struct ide_port_ops svwks_port_ops = {
- .set_pio_mode = svwks_set_pio_mode,
- .set_dma_mode = svwks_set_dma_mode,
- .udma_filter = svwks_udma_filter,
- .cable_detect = svwks_cable_detect,
-};
-
-static const struct ide_port_info serverworks_chipsets[] = {
- { /* 0: OSB4 */
- .name = DRV_NAME,
- .init_chipset = init_chipset_svwks,
- .port_ops = &osb4_port_ops,
- .pio_mask = ATA_PIO4,
- .mwdma_mask = ATA_MWDMA2,
- .udma_mask = 0x00, /* UDMA is problematic on OSB4 */
- },
- { /* 1: CSB5 */
- .name = DRV_NAME,
- .init_chipset = init_chipset_svwks,
- .port_ops = &svwks_port_ops,
- .pio_mask = ATA_PIO4,
- .mwdma_mask = ATA_MWDMA2,
- .udma_mask = ATA_UDMA5,
- },
- { /* 2: CSB6 */
- .name = DRV_NAME,
- .init_chipset = init_chipset_svwks,
- .port_ops = &svwks_port_ops,
- .pio_mask = ATA_PIO4,
- .mwdma_mask = ATA_MWDMA2,
- .udma_mask = ATA_UDMA5,
- },
- { /* 3: CSB6-2 */
- .name = DRV_NAME,
- .init_chipset = init_chipset_svwks,
- .port_ops = &svwks_port_ops,
- .host_flags = IDE_HFLAG_SINGLE,
- .pio_mask = ATA_PIO4,
- .mwdma_mask = ATA_MWDMA2,
- .udma_mask = ATA_UDMA5,
- },
- { /* 4: HT1000 */
- .name = DRV_NAME,
- .init_chipset = init_chipset_svwks,
- .port_ops = &svwks_port_ops,
- .host_flags = IDE_HFLAG_SINGLE,
- .pio_mask = ATA_PIO4,
- .mwdma_mask = ATA_MWDMA2,
- .udma_mask = ATA_UDMA5,
- }
-};
-
-/**
- * svwks_init_one - called when a OSB/CSB is found
- * @dev: the svwks device
- * @id: the matching pci id
- *
- * Called when the PCI registration layer (or the IDE initialization)
- * finds a device matching our IDE device tables.
- */
-
-static int svwks_init_one(struct pci_dev *dev, const struct pci_device_id *id)
-{
- struct ide_port_info d;
- u8 idx = id->driver_data;
-
- d = serverworks_chipsets[idx];
-
- if (idx == 1)
- d.host_flags |= IDE_HFLAG_CLEAR_SIMPLEX;
- else if (idx == 2 || idx == 3) {
- if ((PCI_FUNC(dev->devfn) & 1) == 0) {
- if (pci_resource_start(dev, 0) != 0x01f1)
- d.host_flags |= IDE_HFLAG_NON_BOOTABLE;
- d.host_flags |= IDE_HFLAG_SINGLE;
- } else
- d.host_flags &= ~IDE_HFLAG_SINGLE;
- }
-
- return ide_pci_init_one(dev, &d, NULL);
-}
-
-static const struct pci_device_id svwks_pci_tbl[] = {
- { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE), 0 },
- { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE), 1 },
- { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE), 2 },
- { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2), 3 },
- { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE), 4 },
- { 0, },
-};
-MODULE_DEVICE_TABLE(pci, svwks_pci_tbl);
-
-static struct pci_driver svwks_pci_driver = {
- .name = "Serverworks_IDE",
- .id_table = svwks_pci_tbl,
- .probe = svwks_init_one,
- .remove = ide_pci_remove,
- .suspend = ide_pci_suspend,
- .resume = ide_pci_resume,
-};
-
-static int __init svwks_ide_init(void)
-{
- return ide_pci_register_driver(&svwks_pci_driver);
-}
-
-static void __exit svwks_ide_exit(void)
-{
- pci_unregister_driver(&svwks_pci_driver);
-}
-
-module_init(svwks_ide_init);
-module_exit(svwks_ide_exit);
-
-MODULE_AUTHOR("Michael Aubry. Andrzej Krzysztofowicz, Andre Hedrick, Bartlomiej Zolnierkiewicz");
-MODULE_DESCRIPTION("PCI driver module for Serverworks OSB4/CSB5/CSB6 IDE");
-MODULE_LICENSE("GPL");
--
1.9.1
\
 
 \ /
  Last update: 2016-02-04 15:21    [W:0.466 / U:0.236 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site