lkml.org 
[lkml]   [2016]   [Feb]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 36/51] mtd: nand: gpmi: switch to mtd_ooblayout_ops
Date
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
---
drivers/mtd/nand/gpmi-nand/gpmi-nand.c | 52 ++++++++++++++++++++++++++--------
1 file changed, 40 insertions(+), 12 deletions(-)

diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c
index 3a29b65..316b5ac 100644
--- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c
+++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c
@@ -47,10 +47,44 @@ static struct nand_bbt_descr gpmi_bbt_descr = {
* We may change the layout if we can get the ECC info from the datasheet,
* else we will use all the (page + OOB).
*/
-static struct nand_ecclayout gpmi_hw_ecclayout = {
- .eccbytes = 0,
- .eccpos = { 0, },
- .oobfree = { {.offset = 0, .length = 0} }
+static int gpmi_ooblayout_ecc(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oobregion)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct gpmi_nand_data *this = nand_get_controller_data(chip);
+ struct bch_geometry *geo = &this->bch_geometry;
+
+ if (section)
+ return -ERANGE;
+
+ oobregion->offset = 0;
+ oobregion->length = geo->page_size - mtd->writesize;
+
+ return 0;
+}
+
+static int gpmi_ooblayout_free(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oobregion)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct gpmi_nand_data *this = nand_get_controller_data(chip);
+ struct bch_geometry *geo = &this->bch_geometry;
+
+ if (section)
+ return -ERANGE;
+
+ /* The available oob size we have. */
+ if (geo->page_size < mtd->writesize + mtd->oobsize) {
+ oobregion->offset = geo->page_size - mtd->writesize;
+ oobregion->length = mtd->oobsize - oobregion->offset;
+ }
+
+ return 0;
+}
+
+static const struct mtd_ooblayout_ops gpmi_ooblayout_ops = {
+ .ecc = gpmi_ooblayout_ecc,
+ .free = gpmi_ooblayout_free,
};

static const struct gpmi_devdata gpmi_devdata_imx23 = {
@@ -141,7 +175,6 @@ static int set_geometry_by_ecc_info(struct gpmi_nand_data *this)
struct bch_geometry *geo = &this->bch_geometry;
struct nand_chip *chip = &this->nand;
struct mtd_info *mtd = nand_to_mtd(chip);
- struct nand_oobfree *of = gpmi_hw_ecclayout.oobfree;
unsigned int block_mark_bit_offset;

if (!(chip->ecc_strength_ds > 0 && chip->ecc_step_ds > 0))
@@ -229,12 +262,6 @@ static int set_geometry_by_ecc_info(struct gpmi_nand_data *this)
geo->page_size = mtd->writesize + geo->metadata_size +
(geo->gf_len * geo->ecc_strength * geo->ecc_chunk_count) / 8;

- /* The available oob size we have. */
- if (geo->page_size < mtd->writesize + mtd->oobsize) {
- of->offset = geo->page_size - mtd->writesize;
- of->length = mtd->oobsize - of->offset;
- }
-
geo->payload_size = mtd->writesize;

geo->auxiliary_status_offset = ALIGN(geo->metadata_size, 4);
@@ -1841,6 +1868,7 @@ static void gpmi_nand_exit(struct gpmi_nand_data *this)
static int gpmi_init_last(struct gpmi_nand_data *this)
{
struct nand_chip *chip = &this->nand;
+ struct mtd_info *mtd = nand_to_mtd(chip);
struct nand_ecc_ctrl *ecc = &chip->ecc;
struct bch_geometry *bch_geo = &this->bch_geometry;
int ret;
@@ -1862,7 +1890,7 @@ static int gpmi_init_last(struct gpmi_nand_data *this)
ecc->mode = NAND_ECC_HW;
ecc->size = bch_geo->ecc_chunk_size;
ecc->strength = bch_geo->ecc_strength;
- ecc->layout = &gpmi_hw_ecclayout;
+ mtd_set_ooblayout(mtd, &gpmi_ooblayout_ops);

/*
* We only enable the subpage read when:
--
2.1.4
\
 
 \ /
  Last update: 2016-02-04 12:01    [W:0.158 / U:1.296 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site