lkml.org 
[lkml]   [2016]   [Feb]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 08/11] ARM: dts: sun9i: a80-optimus: Add AXP809 PMIC device node and regulators
Date
The AXP809 PMIC is the primary PMIC. It provides various supply voltages
for the SoC and other peripherals. The PMIC's interrupt line is
connected to NMI pin of the SoC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
arch/arm/boot/dts/sun9i-a80-optimus.dts | 121 +++++++++++++++++++++++++++++++-
1 file changed, 119 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
index 958160e40fd0..7f6bf6138966 100644
--- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
@@ -161,7 +161,7 @@
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_optimus>;
- vmmc-supply = <&reg_vcc3v0>;
+ vmmc-supply = <&reg_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH8 */
cd-inverted;
@@ -171,7 +171,7 @@
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_8bit_pins>;
- vmmc-supply = <&reg_vcc3v0>;
+ vmmc-supply = <&reg_dcdc1>;
bus-width = <8>;
non-removable;
cap-mmc-hw-reset;
@@ -204,6 +204,123 @@

&r_rsb {
status = "okay";
+
+ axp809: pmic@3a3 {
+ reg = <0x3a3>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp809.dtsi"
+
+&reg_aldo1 {
+ /* TODO: This should be handled by the USB PHY driver */
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc33-usbh";
+};
+
+&reg_aldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pb-io-cam";
+};
+
+&reg_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus-09-usbh";
+};
+
+&reg_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v";
+};
+
+&reg_dcdc2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-gpu";
+};
+
+&reg_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpua";
+};
+
+&reg_dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-sys-usb0-hdmi";
+};
+
+&reg_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1425000>;
+ regulator-max-microvolt = <1575000>;
+ regulator-name = "vcc-dram";
+};
+
+&reg_dldo1 {
+ /*
+ * The WiFi chip supports a wide range (3.0 ~ 4.8V) of voltages,
+ * and so does this regulator (3.0 ~ 4.2V), but Allwinner SDK
+ * always sets it to 3.3V.
+ */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+&reg_dldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pl";
+};
+
+&reg_eldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-dvdd-cam";
+};
+
+&reg_eldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pe";
+};
+
+&reg_eldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pm-codec-io1";
+};
+
+&reg_ldo_io0 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pg";
+};
+
+&reg_ldo_io1 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "vcc-pa-gmac-2v5";
+};
+
+&reg_rtc_ldo {
+ regulator-name = "vcc-rtc-vdd1v8-io";
};

&uart0 {
--
2.7.0
\
 
 \ /
  Last update: 2016-02-02 12:01    [W:0.218 / U:0.900 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site