lkml.org 
[lkml]   [2016]   [Dec]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] mm: page_alloc: High-order per-cpu page allocator v7
On Thu, 8 Dec 2016 09:18:06 +0000
Mel Gorman <mgorman@techsingularity.net> wrote:

> On Thu, Dec 08, 2016 at 09:22:31AM +0100, Jesper Dangaard Brouer wrote:
> > On Wed, 7 Dec 2016 23:25:31 +0000
> > Mel Gorman <mgorman@techsingularity.net> wrote:
> >
> > > On Wed, Dec 07, 2016 at 09:19:58PM +0000, Mel Gorman wrote:
> > > > At small packet sizes on localhost, I see relatively low page allocator
> > > > activity except during the socket setup and other unrelated activity
> > > > (khugepaged, irqbalance, some btrfs stuff) which is curious as it's
> > > > less clear why the performance was improved in that case. I considered
> > > > the possibility that it was cache hotness of pages but that's not a
> > > > good fit. If it was true then the first test would be slow and the rest
> > > > relatively fast and I'm not seeing that. The other side-effect is that
> > > > all the high-order pages that are allocated at the start are physically
> > > > close together but that shouldn't have that big an impact. So for now,
> > > > the gain is unexplained even though it happens consistently.
> > > >
> > >
> > > Further investigation led me to conclude that the netperf automation on
> > > my side had some methodology errors that could account for an artifically
> > > low score in some cases. The netperf automation is years old and would
> > > have been developed against a much older and smaller machine which may be
> > > why I missed it until I went back looking at exactly what the automation
> > > was doing. Minimally in a server/client test on remote maching there was
> > > potentially higher packet loss than is acceptable. This would account why
> > > some machines "benefitted" while others did not -- there would be boot to
> > > boot variations that some machines happened to be "lucky". I believe I've
> > > corrected the errors, discarded all the old data and scheduled a rest to
> > > see what falls out.
> >
> > I guess you are talking about setting the netperf socket queue low
> > (+256 bytes above msg size), that I pointed out in[1].
>
> Primarily, yes.
>
> > From the same commit[2] I can see you explicitly set (local+remote):
> >
> > sysctl net.core.rmem_max=16777216
> > sysctl net.core.wmem_max=16777216
> >
>
> Yes, I set it for higher speed networks as a starting point to remind me
> to examine rmem_default or socket configurations if any significant packet
> loss is observed.
>
> > Eric do you have any advice on this setting?
> >
> > And later[4] you further increase this to 32MiB. Notice that the
> > netperf UDP_STREAM test will still use the default value from:
> > net.core.rmem_default = 212992.
> >
>
> That's expected. In the initial sniff-test, I saw negligible packet loss.
> I'm waiting to see what the full set of network tests look like before
> doing any further adjustments.

For netperf I will not recommend adjusting the global default
/proc/sys/net/core/rmem_default as netperf have means of adjusting this
value from the application (which were the options you setup too low
and just removed). I think you should keep this as the default for now
(unless Eric says something else), as this should cover most users.

--
Best regards,
Jesper Dangaard Brouer
MSc.CS, Principal Kernel Engineer at Red Hat
LinkedIn: http://www.linkedin.com/in/brouer

\
 
 \ /
  Last update: 2016-12-08 11:43    [W:0.113 / U:0.100 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site