lkml.org 
[lkml]   [2016]   [Dec]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 1/3] ARM: dts: imx6: Add Savageboard common file
On Sun, Dec 4, 2016 at 11:07 PM, Milo Kim <woogyom.kim@gmail.com> wrote:

> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + reg_3p3v: regulator@0 {
> + compatible = "regulator-fixed";
> + reg = <0>;
> + regulator-name = "3P3V";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };

Please remove the regulators container and put the regulator node
directly as follows:

reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "3P3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
}

> + };
> +};
> +
> +&clks {
> + assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
> + <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
> + assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
> + <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
> +};
> +
> +&fec {
> + phy-mode = "rgmii";
> + phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>;

I think you meant
phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;

> +&iomuxc {
> + savageboard {
> + pinctrl_emmc: emmcgrp {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059
> + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059
> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059
> + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059
> + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059
> + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059
> + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059
> + >;
> + };

You can remove the savegeboard level. Please check
arch/arm/boot/dts/imx6q-tbs2910.dts.

iomux usually go as the last node of the dts file.

\
 
 \ /
  Last update: 2016-12-05 12:37    [W:0.054 / U:1.748 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site