lkml.org 
[lkml]   [2016]   [Dec]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 1/4] pinctrl: aspeed: Read and write bits in LPC and GFX controllers
On Tue, Dec 06, 2016 at 02:11:49PM +1100, Andrew Jeffery wrote:
> The System Control Unit IP block in the Aspeed SoCs is typically where
> the pinmux configuration is found, but not always. A number of pins
> depend on state in one of LPC Host Control (LHC) or SoC Display
> Controller (GFX) IP blocks, so the Aspeed pinmux drivers should have the
> means to adjust these as necessary.
>
> We use syscon to cast a regmap over the GFX and LPC blocks, which is
> used as an arbitration layer between the relevant driver and the pinctrl
> subsystem. The regmaps are then exposed to the SoC-specific pinctrl
> drivers by phandles in the devicetree, and are selected during a mux
> request by querying a new 'ip' member in struct aspeed_sig_desc.
>
> Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
> ---
> .../devicetree/bindings/pinctrl/pinctrl-aspeed.txt | 50 ++++++-
> drivers/pinctrl/aspeed/pinctrl-aspeed-g4.c | 18 +--
> drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c | 48 ++++--
> drivers/pinctrl/aspeed/pinctrl-aspeed.c | 161 +++++++++++++--------
> drivers/pinctrl/aspeed/pinctrl-aspeed.h | 32 ++--
> 5 files changed, 214 insertions(+), 95 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt
> index 2ad18c4ea55c..115b0cce6c1c 100644
> --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt
> @@ -4,12 +4,19 @@ Aspeed Pin Controllers
> The Aspeed SoCs vary in functionality inside a generation but have a common mux
> device register layout.
>
> -Required properties:
> -- compatible : Should be any one of the following:
> - "aspeed,ast2400-pinctrl"
> - "aspeed,g4-pinctrl"
> - "aspeed,ast2500-pinctrl"
> - "aspeed,g5-pinctrl"
> +Required properties for g4:
> +- compatible : Should be any one of the following:
> + "aspeed,ast2400-pinctrl"
> + "aspeed,g4-pinctrl"
> +
> +Required properties for g5:
> +- compatible : Should be any one of the following:
> + "aspeed,ast2500-pinctrl"
> + "aspeed,g5-pinctrl"
> +
> +- aspeed,external-nodes: A cell of phandles to external controller nodes:
> + 0: compatible with "aspeed,ast2500-gfx", "syscon"
> + 1: compatible with "aspeed,ast2500-lpchc", "syscon"
>
> The pin controller node should be a child of a syscon node with the required
> property:
> @@ -47,7 +54,7 @@ RGMII1 RGMII2 RMII1 RMII2 SD1 SPI1 SPI1DEBUG SPI1PASSTHRU TIMER4 TIMER5 TIMER6
> TIMER7 TIMER8 VGABIOSROM
>
>
> -Examples:
> +g4 Example:
>
> syscon: scu@1e6e2000 {
> compatible = "syscon", "simple-mfd";
> @@ -63,5 +70,34 @@ syscon: scu@1e6e2000 {
> };
> };
>
> +g5 Example:
> +
> +apb {
> + gfx: display@1e6e6000 {
> + compatible = "aspeed,ast2500-gfx", "syscon";
> + reg = <0x1e6e6000 0x1000>;
> + };
> +
> + lpchc: lpchc@1e7890a0 {
> + compatible = "aspeed,ast2500-lpchc", "syscon";
> + reg = <0x1e7890a0 0xc4>;
> + };
> +
> + syscon: scu@1e6e2000 {
> + compatible = "syscon", "simple-mfd";

I must have missed this the first time, but "syscon" should be used with
a specific compatible. Though, the scu binding does define one.

> + reg = <0x1e6e2000 0x1a8>;
> +
> + pinctrl: pinctrl {

Is this the only child?

> + compatible = "aspeed,g5-pinctrl";

There's no register range for pinctrl?

> + aspeed,external-nodes = <&gfx, &lpchc>;
> +
> + pinctrl_i2c3_default: i2c3_default {
> + function = "I2C3";
> + groups = "I2C3";
> + };
> + };
> + };
> +};
> +
> Please refer to pinctrl-bindings.txt in this directory for details of the
> common pinctrl bindings used by client devices.

\
 
 \ /
  Last update: 2016-12-12 17:28    [W:0.083 / U:1.164 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site