lkml.org 
[lkml]   [2016]   [Nov]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH v3] ARM: at91/dt: add dts file for sama5d36ek CMP board
Date


> -----Original Message-----
> From: Alexandre Belloni [mailto:alexandre.belloni@free-electrons.com]
> Sent: 2016年11月21日 22:03
> To: Wenyou Yang - A41535 <Wenyou.Yang@microchip.com>
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>; Russell King
> <linux@arm.linux.org.uk>; Rob Herring <robh+dt@kernel.org>; Pawel Moll
> <pawel.moll@arm.com>; Mark Rutland <mark.rutland@arm.com>; Ian Campbell
> <ijc+devicetree@hellion.org.uk>; Kumar Gala <galak@codeaurora.org>; linux-
> kernel@vger.kernel.org; Wenyou Yang - A41535
> <Wenyou.Yang@microchip.com>; devicetree@vger.kernel.org; linux-arm-
> kernel@lists.infradead.org
> Subject: Re: [PATCH v3] ARM: at91/dt: add dts file for sama5d36ek CMP board
>
> Hi,
>
> I fixed it up this time but please use the proper subject prefix next time (ARM: dts:
> at91:).

Thank you.

I keep it in mind.

>
> On 21/11/2016 at 13:14:42 +0800, Wenyou Yang wrote :
> > The sama5d36ek CMP board is the variant of sama5d3xek board.
> > It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865 and some
> > power rail. Its main purpose is used to measure the power consumption.
> > The difference of the sama5d36ek CMP dts from sama5d36ek dts is listed
> > as below.
> > 1. The USB host nodes are removed, that is, the USB host is disabled.
> > 2. The gpio_keys node is added to wake up from the sleep.
> > 3. The LCD isn't supported due to the pins for LCD are conflicted
> > with gpio_keys.
> > 4. The adc0 node support the pinctrl sleep state to fix the over
> > consumption on VDDANA.
> >
> > As said in errata, "When the USB host ports are used in high speed
> > mode (EHCI), it is not possible to suspend the ports if no device is
> > attached on each port. This leads to increased power consumption even
> > if the system is in a low power mode." That is why the the USB host is
> > disabled.
> >
> > Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
> > ---
> >
> > Changes in v3:
> > - Use a dual license scheme for DT files.
> > - Use the proper model name and the compatible string to reflect
> > the nature of this new "CMP" board.
> > - Change name of wakeup property to "wakeup-source".
> > - Remove unnecessary comments.
> > - Remove bootargs.
> >
> > Changes in v2:
> > - Add the pinctrl sleep state for adc0 node to fix the over
> > consumption on VDDANA.
> > - Improve the commit log.
> >
> > arch/arm/boot/dts/sama5d36ek_cmp.dts | 87 ++++++++++
> > arch/arm/boot/dts/sama5d3xcm_cmp.dtsi | 201 +++++++++++++++++++++++
> > arch/arm/boot/dts/sama5d3xmb_cmp.dtsi | 301
> > ++++++++++++++++++++++++++++++++++
> > 3 files changed, 589 insertions(+)
> > create mode 100644 arch/arm/boot/dts/sama5d36ek_cmp.dts
> > create mode 100644 arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
> > create mode 100644 arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
> >
> Applied, thanks.
>
> --
> Alexandre Belloni, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com

Best Regards,
Wenyou Yang
\
 
 \ /
  Last update: 2016-11-22 10:12    [W:0.090 / U:0.720 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site