lkml.org 
[lkml]   [2016]   [Nov]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [RFC PATCH v2 1/7] dt-bindings: document devicetree bindings for mux-gpio
On Thu, Nov 17, 2016 at 10:48:03PM +0100, Peter Rosin wrote:
> ---
> .../devicetree/bindings/misc/mux-gpio.txt | 79 ++++++++++++++++++++++
> 1 file changed, 79 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/misc/mux-gpio.txt
>
> diff --git a/Documentation/devicetree/bindings/misc/mux-gpio.txt b/Documentation/devicetree/bindings/misc/mux-gpio.txt
> new file mode 100644
> index 000000000000..73699a37824f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/misc/mux-gpio.txt
> @@ -0,0 +1,79 @@
> +GPIO-based multiplexer controller bindings
> +
> +Define what GPIO pins are used to control a multiplexer. Or several
> +multiplexers, if the same pins control more than one multiplexer.

I think this makes sense in your case, but I think it is too complicated
for a non-shared case. Perhaps mux-gpios should be used directly (i.e.
in the adc-mux node) and control-muxes only used for the shared case.

Part of me feels like you are working around in DT the GPIO subsystem
limitation that it can't share GPIO lines. Either this could be fixed
in some way in the GPIO subsystem, or the mux subsys could deal with it.
You just have to look up if you already have a mux registered for the
same GPIOs. Of course, that may make the mux subsys pretty much GPIO
only, but I'm having a hard time thinking how you would have shared
muxes that are not GPIO controlled. Any other control would be
integrated into the mux itself.

> +
> +Required properties:
> +- compatible : "mux-gpio"
> +- mux-gpios : list of gpios used to control the multiplexer, least
> + significant bit first.
> +
> +Optional properties:
> +- idle-state : if present, the state the mux will have when idle.

Needs some detail on what the value is. One bit per gpio? One cell per
gpio?

> +
> +Example:
> + control_mux: control-adc-mux {
> + compatible = "mux-gpio";
> +
> + mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>,
> + <&pioA 1 GPIO_ACTIVE_HIGH>;
> + };
> +
> + adc-mux {
> + compatible = "iio-mux";
> + io-channels = <&adc 0>;
> + io-channel-names = "parent";
> +
> + control-muxes = <&control_mux>;

This is a common name? It should be in a common mux binding doc.

> + control-mux-names = "mux";

I think this can be dropped at least until you have more than 1.

> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + sync-1@0 {
> + reg = <0>;
> + };
> +
> + in@1 {
> + reg = <1>;
> + };
> +
> + out@2 {
> + reg = <2>;
> + };
> +
> + sync-2@3 {
> + reg = <3>;
> + };
> + };
> +
> + i2c-mux {
> + compatible = "i2c-mux-simple,mux-locked";
> + i2c-parent = <&i2c1>;
> +
> + control-muxes = <&control_mux>;
> + control-mux-names = "mux";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c@0 {
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ssd1307: oled@3c {
> + /* ... */
> + };
> + };
> +
> + i2c@3 {
> + reg = <3>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pca9555: pca9555@20 {
> + /* ... */
> + };
> + };
> + };
> --
> 2.1.4
>

\
 
 \ /
  Last update: 2016-11-18 16:36    [W:0.419 / U:0.180 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site