lkml.org 
[lkml]   [2016]   [Oct]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH V2 4/6] serial: 8250_fintek: Add F81216 Support
Date
Fintek F81216 is a LPC to 4 UARTs device. It's the F81216 series but
support less functional than F81216AD/F81216H

The following list is brief descriptions of F81216 series:

F81216H (0105)
9Bit/High baud rate(not implements with mainline)
RS485, 128Bytes FIFO (implemented)

F81216AD (0216)
9Bit(not implements with mainline)
RS485(implemented)

F81216 (0208)
basically 16550A

Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
---
drivers/tty/serial/8250/8250_fintek.c | 26 ++++++++++++++++++++++++--
1 file changed, 24 insertions(+), 2 deletions(-)

diff --git a/drivers/tty/serial/8250/8250_fintek.c b/drivers/tty/serial/8250/8250_fintek.c
index e039a33..523d873 100644
--- a/drivers/tty/serial/8250/8250_fintek.c
+++ b/drivers/tty/serial/8250/8250_fintek.c
@@ -23,6 +23,7 @@
#define CHIP_ID2 0x21
#define CHIP_ID_F81216AD 0x1602
#define CHIP_ID_F81216H 0x0501
+#define CHIP_ID_F81216 0x0802
#define VENDOR_ID1 0x23
#define VENDOR_ID1_VAL 0x19
#define VENDOR_ID2 0x24
@@ -107,8 +108,14 @@ static int fintek_8250_check_id(struct fintek_8250 *pdata)
chip = sio_read_reg(pdata, CHIP_ID1);
chip |= sio_read_reg(pdata, CHIP_ID2) << 8;

- if (chip != CHIP_ID_F81216AD && chip != CHIP_ID_F81216H)
+ switch (chip) {
+ case CHIP_ID_F81216AD:
+ case CHIP_ID_F81216H:
+ case CHIP_ID_F81216:
+ break;
+ default:
return -ENODEV;
+ }

pdata->pid = chip;
return 0;
@@ -235,6 +242,21 @@ static int probe_setup_port(struct fintek_8250 *pdata, u16 io_address,
return -ENODEV;
}

+static void fintek_8250_set_rs485_handler(struct uart_8250_port *uart)
+{
+ struct fintek_8250 *pdata = uart->port.private_data;
+
+ switch (pdata->pid) {
+ case CHIP_ID_F81216AD:
+ case CHIP_ID_F81216H:
+ uart->port.rs485_config = fintek_8250_rs485_config;
+ break;
+
+ default: /* No RS485 Auto direction functional */
+ break;
+ }
+}
+
int fintek_8250_probe(struct uart_8250_port *uart)
{
struct fintek_8250 *pdata;
@@ -248,8 +270,8 @@ int fintek_8250_probe(struct uart_8250_port *uart)
return -ENOMEM;

memcpy(pdata, &probe_data, sizeof(probe_data));
- uart->port.rs485_config = fintek_8250_rs485_config;
uart->port.private_data = pdata;
+ fintek_8250_set_rs485_handler(uart);

return 0;
}
--
1.9.1
\
 
 \ /
  Last update: 2016-10-04 10:29    [W:0.076 / U:0.056 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site