lkml.org 
[lkml]   [2016]   [Oct]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 7/7] i2c: bcm2835: Add support for dynamic clock
Date
Support a dynamic clock by reading the frequency and setting the
divisor in the transfer function instead of during probe.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Martin Sperl <kernel@martin.sperl.org>
---
drivers/i2c/busses/i2c-bcm2835.c | 51 +++++++++++++++++++++++++---------------
1 file changed, 32 insertions(+), 19 deletions(-)

diff --git a/drivers/i2c/busses/i2c-bcm2835.c b/drivers/i2c/busses/i2c-bcm2835.c
index d2085dd..c3436f6 100644
--- a/drivers/i2c/busses/i2c-bcm2835.c
+++ b/drivers/i2c/busses/i2c-bcm2835.c
@@ -58,6 +58,7 @@ struct bcm2835_i2c_dev {
void __iomem *regs;
struct clk *clk;
int irq;
+ u32 bus_clk_rate;
struct i2c_adapter adapter;
struct completion completion;
struct i2c_msg *curr_msg;
@@ -78,6 +79,30 @@ static inline u32 bcm2835_i2c_readl(struct bcm2835_i2c_dev *i2c_dev, u32 reg)
return readl(i2c_dev->regs + reg);
}

+static int bcm2835_i2c_set_divider(struct bcm2835_i2c_dev *i2c_dev)
+{
+ u32 divider;
+
+ divider = DIV_ROUND_UP(clk_get_rate(i2c_dev->clk),
+ i2c_dev->bus_clk_rate);
+ /*
+ * Per the datasheet, the register is always interpreted as an even
+ * number, by rounding down. In other words, the LSB is ignored. So,
+ * if the LSB is set, increment the divider to avoid any issue.
+ */
+ if (divider & 1)
+ divider++;
+ if ((divider < BCM2835_I2C_CDIV_MIN) ||
+ (divider > BCM2835_I2C_CDIV_MAX)) {
+ dev_err_ratelimited(i2c_dev->dev, "Invalid clock-frequency\n");
+ return -EINVAL;
+ }
+
+ bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_DIV, divider);
+
+ return 0;
+}
+
static void bcm2835_fill_txfifo(struct bcm2835_i2c_dev *i2c_dev)
{
u32 val;
@@ -224,7 +249,7 @@ static int bcm2835_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[],
{
struct bcm2835_i2c_dev *i2c_dev = i2c_get_adapdata(adap);
unsigned long time_left;
- int i;
+ int i, ret;

for (i = 0; i < (num - 1); i++)
if (msgs[i].flags & I2C_M_RD) {
@@ -233,6 +258,10 @@ static int bcm2835_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[],
return -EOPNOTSUPP;
}

+ ret = bcm2835_i2c_set_divider(i2c_dev);
+ if (ret)
+ return ret;
+
i2c_dev->curr_msg = msgs;
i2c_dev->num_msgs = num;
reinit_completion(&i2c_dev->completion);
@@ -282,7 +311,6 @@ static int bcm2835_i2c_probe(struct platform_device *pdev)
{
struct bcm2835_i2c_dev *i2c_dev;
struct resource *mem, *irq;
- u32 bus_clk_rate, divider;
int ret;
struct i2c_adapter *adap;

@@ -306,27 +334,12 @@ static int bcm2835_i2c_probe(struct platform_device *pdev)
}

ret = of_property_read_u32(pdev->dev.of_node, "clock-frequency",
- &bus_clk_rate);
+ &i2c_dev->bus_clk_rate);
if (ret < 0) {
dev_warn(&pdev->dev,
"Could not read clock-frequency property\n");
- bus_clk_rate = 100000;
- }
-
- divider = DIV_ROUND_UP(clk_get_rate(i2c_dev->clk), bus_clk_rate);
- /*
- * Per the datasheet, the register is always interpreted as an even
- * number, by rounding down. In other words, the LSB is ignored. So,
- * if the LSB is set, increment the divider to avoid any issue.
- */
- if (divider & 1)
- divider++;
- if ((divider < BCM2835_I2C_CDIV_MIN) ||
- (divider > BCM2835_I2C_CDIV_MAX)) {
- dev_err(&pdev->dev, "Invalid clock-frequency\n");
- return -ENODEV;
+ i2c_dev->bus_clk_rate = 100000;
}
- bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_DIV, divider);

irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
if (!irq) {
--
2.8.2
\
 
 \ /
  Last update: 2016-10-03 22:08    [W:0.045 / U:0.284 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site