lkml.org 
[lkml]   [2016]   [Oct]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v6] tty/serial: at91: fix hardware handshake on Atmel platforms
From
Date
Le 27/10/2016 à 18:04, Richard Genoud a écrit :
> After commit 1cf6e8fc8341 ("tty/serial: at91: fix RTS line management
> when hardware handshake is enabled"), the hardware handshake wasn't
> functional anymore on Atmel platforms (beside SAMA5D2).
>
> To understand why, one has to understand the flag ATMEL_US_USMODE_HWHS
> first:
> Before commit 1cf6e8fc8341 ("tty/serial: at91: fix RTS line management
> when hardware handshake is enabled"), this flag was never set.
> Thus, the CTS/RTS where only handled by serial_core (and everything
> worked just fine).
>
> This commit introduced the use of the ATMEL_US_USMODE_HWHS flag,
> enabling it for all boards when the user space enables flow control.
>
> When the ATMEL_US_USMODE_HWHS is set, the Atmel USART controller
> handles a part of the flow control job:
> - disable the transmitter when the CTS pin gets high.
> - drive the RTS pin high when the DMA buffer transfer is completed or
> PDC RX buffer full or RX FIFO is beyond threshold. (depending on the
> controller version).
>
> NB: This feature is *not* mandatory for the flow control to work.
> (Nevertheless, it's very useful if low latencies are needed.)
>
> Now, the specifics of the ATMEL_US_USMODE_HWHS flag:
>
> - For platforms with DMAC and no FIFOs (sam9x25, sam9x35, sama5D3,
> sama5D4, sam9g15, sam9g25, sam9g35)* this feature simply doesn't work.
> ( source: https://lkml.org/lkml/2016/9/7/598 )
> Tested it on sam9g35, the RTS pins always stays up, even when RXEN=1
> or a new DMA transfer descriptor is set.
> => ATMEL_US_USMODE_HWHS must not be used for those platforms
>
> - For platforms with a PDC (sam926{0,1,3}, sam9g10, sam9g20, sam9g45,
> sam9g46)*, there's another kind of problem. Once the flag
> ATMEL_US_USMODE_HWHS is set, the RTS pin can't be driven anymore via
> RTSEN/RTSDIS in USART Control Register. The RTS pin can only be driven
> by enabling/disabling the receiver or setting RCR=RNCR=0 in the PDC
> (Receive (Next) Counter Register).
> => Doing this is beyond the scope of this patch and could add other
> bugs, so the original (and working) behaviour should be set for those
> platforms (meaning ATMEL_US_USMODE_HWHS flag should be unset).
>
> - For platforms with a FIFO (sama5d2)*, the RTS pin is driven according
> to the RX FIFO thresholds, and can be also driven by RTSEN/RTSDIS in
> USART Control Register. No problem here.
> (This was the use case of commit 1cf6e8fc8341 ("tty/serial: at91: fix
> RTS line management when hardware handshake is enabled"))
> NB: If the CTS pin declared as a GPIO in the DTS, (for instance
> cts-gpios = <&pioA PIN_PB31 GPIO_ACTIVE_LOW>), the transmitter will be
> disabled.
> => ATMEL_US_USMODE_HWHS flag can be set for this platform ONLY IF the
> CTS pin is not a GPIO.
>
> So, the only case when ATMEL_US_USMODE_HWHS can be enabled is when
> (atmel_use_fifo(port) &&
> !mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS))
>
> Tested on all Atmel USART controller flavours:
> AT91SAM9G35-CM (DMAC flavour), AT91SAM9G20-EK (PDC flavour),
> SAMA5D2xplained (FIFO flavour).
>
> * the list may not be exhaustive
>
> Cc: <stable@vger.kernel.org> #4.4+ (beware, missing atmel_port variable)
> Fixes: 1cf6e8fc8341 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled")
> Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Thanks

> ---
> drivers/tty/serial/atmel_serial.c | 26 ++++++++++++++++++++++----
> 1 file changed, 22 insertions(+), 4 deletions(-)
>
> Note for -stable:
> This patch will apply on 4.4.x/4.8.x but compilation will fail due to
> a missing variable atmel_port (introduced in 4.9-rc1):
>
> static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
> struct ktermios *old)
> {
> + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
> unsigned long flags;
> unsigned int old_mode, mode, imr, quot, baud;
>
> Changes since v5:
> - fix typos
> - increase commentary
>
> Changes since v4:
> - the mctrl_gpio_use_rtscts() is gone since it was atmel_serial
> specific. (so patch 1 is gone)
> - patches 2 and 3 have been merged together since it didn't make
> a lot of sense to correct the GPIO case in one separate patch.
> - ATMEL_US_USMODE_HWHS is now unset for platform with PDC
>
> Changes since v3:
> - remove superfluous #include <linux/err.h> (thanks to Uwe)
> - rebase on next-20160930
>
> Changes since v2:
> - remove IS_ERR_OR_NULL() test in patch 1/3 as Uwe suggested.
> - fix typos in patch 2/3
> - rebase on next-20160927
> - simplify the logic in patch 3/3.
>
> Changes since v1:
> - Correct patch 1 with the error found by kbuild.
> - Add Alexandre's Acked-by on patch 2
> - Rewrite patch 3 logic in the light of the on-going discussion
> with Cyrille and Alexandre.
>
>
> diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
> index fd8aa1f4ba78..168b10cad47b 100644
> --- a/drivers/tty/serial/atmel_serial.c
> +++ b/drivers/tty/serial/atmel_serial.c
> @@ -2132,11 +2132,29 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
> mode |= ATMEL_US_USMODE_RS485;
> } else if (termios->c_cflag & CRTSCTS) {
> /* RS232 with hardware handshake (RTS/CTS) */
> - if (atmel_use_dma_rx(port) && !atmel_use_fifo(port)) {
> - dev_info(port->dev, "not enabling hardware flow control because DMA is used");
> - termios->c_cflag &= ~CRTSCTS;
> - } else {
> + if (atmel_use_fifo(port) &&
> + !mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS)) {
> + /*
> + * with ATMEL_US_USMODE_HWHS set, the controller will
> + * be able to drive the RTS pin high/low when the RX
> + * FIFO is above RXFTHRES/below RXFTHRES2.
> + * It will also disable the transmitter when the CTS
> + * pin is high.
> + * This mode is not activated if CTS pin is a GPIO
> + * because in this case, the transmitter is always
> + * disabled (there must be an internal pull-up
> + * responsible for this behaviour).
> + * If the RTS pin is a GPIO, the controller won't be
> + * able to drive it according to the FIFO thresholds,
> + * but it will be handled by the driver.
> + */
> mode |= ATMEL_US_USMODE_HWHS;
> + } else {
> + /*
> + * For platforms without FIFO, the flow control is
> + * handled by the driver.
> + */
> + mode |= ATMEL_US_USMODE_NORMAL;
> }
> } else {
> /* RS232 without hadware handshake */
>


--
Nicolas Ferre

\
 
 \ /
  Last update: 2016-10-27 18:09    [W:0.101 / U:0.740 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site