lkml.org 
[lkml]   [2016]   [Oct]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 3/4] serial: 8250_uniphier: hardcode regshift to avoid unneeded memory read
Date
For this driver, uart_port::regshift is always 2.  Hardcode the
shift value instead of reading ->regshift to get an already known
value. (pointed out by Denys Vlasenko)

Furthermore, I am using register macros that are already shifted,
which will save code a bit.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
---

drivers/tty/serial/8250/8250_uniphier.c | 42 +++++++++++++++++++--------------
1 file changed, 24 insertions(+), 18 deletions(-)

diff --git a/drivers/tty/serial/8250/8250_uniphier.c b/drivers/tty/serial/8250/8250_uniphier.c
index 417d9e7..92e7bb7 100644
--- a/drivers/tty/serial/8250/8250_uniphier.c
+++ b/drivers/tty/serial/8250/8250_uniphier.c
@@ -24,10 +24,22 @@
/* Most (but not all) of UniPhier UART devices have 64-depth FIFO. */
#define UNIPHIER_UART_DEFAULT_FIFO_SIZE 64

-#define UNIPHIER_UART_CHAR_FCR 3 /* Character / FIFO Control Register */
-#define UNIPHIER_UART_LCR_MCR 4 /* Line/Modem Control Register */
-#define UNIPHIER_UART_LCR_SHIFT 8
-#define UNIPHIER_UART_DLR 9 /* Divisor Latch Register */
+/*
+ * This hardware is similar to 8250, but its register map is a bit different:
+ * - MMIO32 (regshift = 2)
+ * - FCR is not at 2, but 3
+ * - LCR and MCR are not at 3 and 4, they share 4
+ * - Divisor latch at 9, no divisor latch access bit
+ */
+
+#define UNIPHIER_UART_REGSHIFT 2
+
+/* bit[15:8] = CHAR (not used), bit[7:0] = FCR */
+#define UNIPHIER_UART_CHAR_FCR (3 << (UNIPHIER_UART_REGSHIFT))
+/* bit[15:8] = LCR, bit[7:0] = MCR */
+#define UNIPHIER_UART_LCR_MCR (4 << (UNIPHIER_UART_REGSHIFT))
+/* Divisor Latch Register */
+#define UNIPHIER_UART_DLR (9 << (UNIPHIER_UART_REGSHIFT))

struct uniphier8250_priv {
int line;
@@ -44,7 +56,7 @@ static int __init uniphier_early_console_setup(struct earlycon_device *device,

/* This hardware always expects MMIO32 register interface. */
device->port.iotype = UPIO_MEM32;
- device->port.regshift = 2;
+ device->port.regshift = UNIPHIER_UART_REGSHIFT;

/*
* Do not touch the divisor register in early_serial8250_setup();
@@ -68,17 +80,16 @@ static unsigned int uniphier_serial_in(struct uart_port *p, int offset)

switch (offset) {
case UART_LCR:
- valshift = UNIPHIER_UART_LCR_SHIFT;
+ valshift = 8;
/* fall through */
case UART_MCR:
offset = UNIPHIER_UART_LCR_MCR;
break;
default:
+ offset <<= UNIPHIER_UART_REGSHIFT;
break;
}

- offset <<= p->regshift;
-
/*
* The return value must be masked with 0xff because LCR and MCR reside
* in the same register that must be accessed by 32-bit write/read.
@@ -97,7 +108,7 @@ static void uniphier_serial_out(struct uart_port *p, int offset, int value)
offset = UNIPHIER_UART_CHAR_FCR;
break;
case UART_LCR:
- valshift = UNIPHIER_UART_LCR_SHIFT;
+ valshift = 8;
/* Divisor latch access bit does not exist. */
value &= ~UART_LCR_DLAB;
/* fall through */
@@ -106,11 +117,10 @@ static void uniphier_serial_out(struct uart_port *p, int offset, int value)
break;
default:
normal = true;
+ offset <<= UNIPHIER_UART_REGSHIFT;
break;
}

- offset <<= p->regshift;
-
if (normal) {
writel(value, p->membase + offset);
} else {
@@ -139,16 +149,12 @@ static void uniphier_serial_out(struct uart_port *p, int offset, int value)
*/
static int uniphier_serial_dl_read(struct uart_8250_port *up)
{
- int offset = UNIPHIER_UART_DLR << up->port.regshift;
-
- return readl(up->port.membase + offset);
+ return readl(up->port.membase + UNIPHIER_UART_DLR);
}

static void uniphier_serial_dl_write(struct uart_8250_port *up, int value)
{
- int offset = UNIPHIER_UART_DLR << up->port.regshift;
-
- writel(value, up->port.membase + offset);
+ writel(value, up->port.membase + UNIPHIER_UART_DLR);
}

static int uniphier_of_serial_setup(struct device *dev, struct uart_port *port,
@@ -234,7 +240,7 @@ static int uniphier_uart_probe(struct platform_device *pdev)

up.port.type = PORT_16550A;
up.port.iotype = UPIO_MEM32;
- up.port.regshift = 2;
+ up.port.regshift = UNIPHIER_UART_REGSHIFT;
up.port.flags = UPF_FIXED_PORT | UPF_FIXED_TYPE;
up.capabilities = UART_CAP_FIFO;

--
1.9.1
\
 
 \ /
  Last update: 2016-10-24 10:00    [W:0.349 / U:0.240 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site