lkml.org 
[lkml]   [2016]   [Oct]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] mfd: rk808: RK818 uses DEV_OFF to power off supplies
From
Date
Hi Wadim:

It's impossible not to restart automatically, this situation is
normal for RK818.
Because it is hardware designed that RK818 can't power off when a
voltage is supplies on the USB supply input pins.



Best Regards

在 2016/10/21 15:44, Wadim Egorov 写道:
> Hi Jianhong,
>
> with this patch a poweroff causes a restart on our board.
> In our design a 5V USB voltage is supplied on the USB supply input pins.
> After setting DEV_OFF bit, the RK818 restart automatically. The
> ON_SOURCE_REG (Address AEH) is 0x40 after the automatic restart which
> says that the RK818 was started by ON_PLUG_IN event.
> Is there a possibility to configure the RK818 that it will not start
> automatically in this case?
>
> Regards,
> Wadim
>
> On 17.10.2016 11:03, Jianhong Chen wrote:
>> DEV_OFF and DEV_OFF_RST functions for RK808 are designed error that
>> only DEV_OFF_RST can power off supplies. RK818 has been fixed this
>> issue, so that DEV_OFF is used to power off supplies.
>>
>> Signed-off-by: Jianhong Chen <chenjh@rock-chips.com>
>> ---
>> drivers/mfd/rk808.c | 23 ++++++++++++++++++++++-
>> include/linux/mfd/rk808.h | 1 +
>> 2 files changed, 23 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/mfd/rk808.c b/drivers/mfd/rk808.c
>> index 0f8acc5..2c9acdb 100644
>> --- a/drivers/mfd/rk808.c
>> +++ b/drivers/mfd/rk808.c
>> @@ -290,6 +290,24 @@ static void rk808_device_shutdown(void)
>> dev_err(&rk808_i2c_client->dev, "power off error!\n");
>> }
>>
>> +static void rk818_device_shutdown(void)
>> +{
>> + int ret;
>> + struct rk808 *rk808 = i2c_get_clientdata(rk808_i2c_client);
>> +
>> + if (!rk808) {
>> + dev_warn(&rk808_i2c_client->dev,
>> + "have no rk818, so do nothing here\n");
>> + return;
>> + }
>> +
>> + ret = regmap_update_bits(rk808->regmap,
>> + RK818_DEVCTRL_REG,
>> + DEV_OFF, DEV_OFF);
>> + if (ret)
>> + dev_err(&rk808_i2c_client->dev, "power off error!\n");
>> +}
>> +
>> static const struct of_device_id rk808_of_match[] = {
>> { .compatible = "rockchip,rk808" },
>> { .compatible = "rockchip,rk818" },
>> @@ -304,6 +322,7 @@ static int rk808_probe(struct i2c_client *client,
>> struct rk808 *rk808;
>> const struct rk808_reg_data *pre_init_reg;
>> const struct mfd_cell *cells;
>> + void (*pm_pwroff_fn)(void);
>> int nr_pre_init_regs;
>> int nr_cells;
>> int pm_off = 0;
>> @@ -331,6 +350,7 @@ static int rk808_probe(struct i2c_client *client,
>> nr_pre_init_regs = ARRAY_SIZE(rk808_pre_init_reg);
>> cells = rk808s;
>> nr_cells = ARRAY_SIZE(rk808s);
>> + pm_pwroff_fn = rk808_device_shutdown;
>> break;
>> case RK818_ID:
>> rk808->regmap_cfg = &rk818_regmap_config;
>> @@ -339,6 +359,7 @@ static int rk808_probe(struct i2c_client *client,
>> nr_pre_init_regs = ARRAY_SIZE(rk818_pre_init_reg);
>> cells = rk818s;
>> nr_cells = ARRAY_SIZE(rk818s);
>> + pm_pwroff_fn = rk818_device_shutdown;
>> break;
>> default:
>> dev_err(&client->dev, "Unsupported RK8XX ID %lu\n",
>> @@ -393,7 +414,7 @@ static int rk808_probe(struct i2c_client *client,
>> "rockchip,system-power-controller");
>> if (pm_off && !pm_power_off) {
>> rk808_i2c_client = client;
>> - pm_power_off = rk808_device_shutdown;
>> + pm_power_off = pm_pwroff_fn;
>> }
>>
>> return 0;
>> diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h
>> index 6d435a3..83701ef 100644
>> --- a/include/linux/mfd/rk808.h
>> +++ b/include/linux/mfd/rk808.h
>> @@ -290,6 +290,7 @@ enum rk818_reg {
>> #define SWITCH2_EN BIT(6)
>> #define SWITCH1_EN BIT(5)
>> #define DEV_OFF_RST BIT(3)
>> +#define DEV_OFF BIT(0)
>>
>> #define VB_LO_ACT BIT(4)
>> #define VB_LO_SEL_3500MV (7 << 0)
>
>
>


\
 
 \ /
  Last update: 2016-10-21 11:16    [W:0.093 / U:1.092 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site