lkml.org 
[lkml]   [2016]   [Jan]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/2] phy: ti-pipe3: configure usb3 phy to be used as pcie phy
Date
DRA72 uses USB3 PHY for the 2nd lane of PCIE. The configuration
required to make USB3 PHY used for the 2nd lane of PCIe is done
here.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
Documentation/devicetree/bindings/phy/ti-phy.txt | 2 ++
drivers/phy/phy-ti-pipe3.c | 30 +++++++++++++++++++++-
2 files changed, 31 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt
index a3b3945..6a7de94 100644
--- a/Documentation/devicetree/bindings/phy/ti-phy.txt
+++ b/Documentation/devicetree/bindings/phy/ti-phy.txt
@@ -91,6 +91,8 @@ Optional properties:
register that contains the SATA_PLL_SOFT_RESET bit. Only valid for sata_phy.
- syscon-pcs : phandle/offset pair. Phandle to the system control module and the
register offset to write the PCS delay value.
+ - "ti,configure-as-pcie" : property to indicate if the PHY should be
+ configured as PCIE PHY.

Deprecated properties:
- ctrl-module : phandle of the control module used by PHY driver to power on
diff --git a/drivers/phy/phy-ti-pipe3.c b/drivers/phy/phy-ti-pipe3.c
index 7d83d2b..793185e 100644
--- a/drivers/phy/phy-ti-pipe3.c
+++ b/drivers/phy/phy-ti-pipe3.c
@@ -56,6 +56,12 @@

#define SATA_PLL_SOFT_RESET BIT(18)

+#define PHY_RX_ANA_PRGRAMMABILITY_REG 0xC
+#define MEM_EN_PLLBYP BIT(7)
+
+#define PHY_TX_TEST_CONFIG 0x2C
+#define MEM_ENTESTCLK BIT(31)
+
#define PIPE3_PHY_PWRCTL_CLK_CMD_MASK 0x003FC000
#define PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT 14

@@ -68,6 +74,10 @@
#define PCIE_PCS_MASK 0xFF0000
#define PCIE_PCS_DELAY_COUNT_SHIFT 0x10

+#define PIPE3_PHY_DISABLE_SYNC_POWER BIT(4)
+
+#define CONFIGURE_AS_PCIE BIT(0)
+
/*
* This is an Empirical value that works, need to confirm the actual
* value required for the PIPE3PHY_PLL_CONFIGURATION2.PLL_IDLE status
@@ -90,6 +100,7 @@ struct pipe3_dpll_map {
};

struct ti_pipe3 {
+ u32 flags;
void __iomem *pll_ctrl_base;
void __iomem *phy_rx;
void __iomem *phy_tx;
@@ -270,6 +281,19 @@ static int ti_pipe3_init(struct phy *x)
int ret = 0;

ti_pipe3_enable_clocks(phy);
+
+ if (phy->flags & CONFIGURE_AS_PCIE) {
+ val = ti_pipe3_readl(phy->phy_rx,
+ PHY_RX_ANA_PRGRAMMABILITY_REG);
+ val |= MEM_EN_PLLBYP;
+ ti_pipe3_writel(phy->phy_rx, PHY_RX_ANA_PRGRAMMABILITY_REG,
+ val);
+ val = ti_pipe3_readl(phy->phy_tx, PHY_TX_TEST_CONFIG);
+ val |= MEM_ENTESTCLK;
+ ti_pipe3_writel(phy->phy_tx, PHY_TX_TEST_CONFIG, val);
+ return 0;
+ }
+
/*
* Set pcie_pcs register to 0x96 for proper functioning of phy
* as recommended in AM572x TRM SPRUHZ6, section 18.5.2.2, table
@@ -318,7 +342,8 @@ static int ti_pipe3_exit(struct phy *x)
return 0;

/* PCIe doesn't have internal DPLL */
- if (!of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-pcie")) {
+ if (!of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-pcie") &&
+ !(phy->flags & CONFIGURE_AS_PCIE)) {
/* Put DPLL in IDLE mode */
val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2);
val |= PLL_IDLE;
@@ -590,6 +615,9 @@ static int ti_pipe3_probe(struct platform_device *pdev)
if (ret)
return ret;

+ if (of_property_read_bool(node, "ti,configure-as-pcie"))
+ phy->flags |= CONFIGURE_AS_PCIE;
+
platform_set_drvdata(pdev, phy);
pm_runtime_enable(dev);

--
1.7.9.5


\
 
 \ /
  Last update: 2016-01-06 12:41    [W:0.050 / U:0.556 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site