lkml.org 
[lkml]   [2015]   [Sep]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v4 1/5] Documentation: add DT bindings for ARM SCPI sensors
Date
Punit Agrawal <punit.agrawal@arm.com> writes:

> Punit Agrawal <punit.agrawal@arm.com> writes:
>
>> The System Control Processor (SCP) provides access to SoC sensors via
>> the System Control and Power Interface (SCPI) Message Protocol. Add
>> bindings to allow probing of these sensors. Also support referencing
>> of the sensors for setting up thermal zones via the thermal DT
>> bindings.
>>
>> Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
>> Cc: Rob Herring <robh+dt@kernel.org>
>> Cc: Mark Rutland <mark.rutland@arm.com>
>> Cc: Sudeep Holla <sudeep.holla@arm.com>
>
> Gentle reminder for review of the below bindings. They've been updated
> based on feedback on the earlier version [a].
>
> If there are no further comments, I'd like to request an ack from the DT
> reviewers.

Ping!

>
> [a] http://thread.gmane.org/gmane.linux.power-management.general/65475/focus=134976
>
>> ---
>> Documentation/devicetree/bindings/arm/arm,scpi.txt | 38 ++++++++++++++++++++++
>> 1 file changed, 38 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/arm/arm,scpi.txt b/Documentation/devicetree/bindings/arm/arm,scpi.txt
>> index f002460..86302de 100644
>> --- a/Documentation/devicetree/bindings/arm/arm,scpi.txt
>> +++ b/Documentation/devicetree/bindings/arm/arm,scpi.txt
>> @@ -72,8 +72,25 @@ Required sub-node properties:
>> - compatible : should be "arm,juno-scp-shmem" for Non-secure SRAM based
>> shared memory on Juno platforms
>>
>> +Sensor bindings for the sensors based on SCPI Message Protocol
>> +--------------------------------------------------------------
>> +SCPI provides an API to access the various sensors on the SoC.
>> +
>> +Required properties:
>> +- compatible : should be "arm,scpi-sensors".
>> +- #thermal-sensor-cells: should be set to 1. This property follows the
>> + thermal device tree bindings[2].
>> +
>> + Valid cell values are raw identifiers (Sensor
>> + ID) as used by the firmware. Refer to
>> + platform documentation for your
>> + implementation for the IDs to use. For Juno
>> + R0 and Juno R1 refer to [3].
>> +
>> [0] http://infocenter.arm.com/help/topic/com.arm.doc.dui0922b/index.html
>> [1] Documentation/devicetree/bindings/clock/clock-bindings.txt
>> +[2] Documentation/devicetree/bindings/thermal/thermal.txt
>> +[3] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0922b/apas03s22.html
>>
>> Example:
>>
>> @@ -122,6 +139,11 @@ scpi_protocol: scpi@2e000000 {
>> clock-output-names = "pxlclk0", "pxlclk1";
>> };
>> };
>> +
>> + scpi_sensors0: sensors {
>> + compatible = "arm,scpi-sensors";
>> + #thermal-sensor-cells = <1>;
>> + };
>> };
>>
>> cpu@0 {
>> @@ -136,6 +158,17 @@ hdlcd@7ff60000 {
>> clocks = <&scpi_clk 4>;
>> };
>>
>> +thermal-zones {
>> + soc_thermal {
>> + polling-delay-passive = <100>;
>> + polling-delay = <1000>;
>> +
>> + /* sensor ID */
>> + thermal-sensors = <&scpi_sensors0 3>;
>> + ...
>> + };
>> +};
>> +
>> In the above example, the #clock-cells is set to 1 as required.
>> scpi_dvfs has 3 output clocks namely: atlclk, aplclk, and gpuclk with 0,
>> 1 and 2 as clock-indices. scpi_clk has 2 output clocks namely: pxlclk0
>> @@ -148,3 +181,8 @@ scpi_dvfs i.e. "atlclk".
>> Similarly the second example is hdlcd@7ff60000 and it has pxlclk1 as input
>> clock. '4' in the clock specifier here points to the second entry
>> in the output clocks of scpi_clocks i.e. "pxlclk1"
>> +
>> +The thermal-sensors property in the soc_thermal node uses the
>> +temperature sensor provided by SCP firmware to setup a thermal
>> +zone. The ID "3" is the sensor identifier for the temperature sensor
>> +as used by the firmware.
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html


\
 
 \ /
  Last update: 2015-09-29 17:21    [W:0.947 / U:0.024 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site