lkml.org 
[lkml]   [2015]   [Sep]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] ARM: dts: keystone: use one to one address translations under netcp
On 09/02/2015 02:25 PM, santosh shilimkar wrote:
> 9/2/2015 10:58 AM, Murali Karicheri wrote:
>> On 09/02/2015 01:24 PM, santosh shilimkar wrote:
>>> On 9/2/2015 9:35 AM, Murali Karicheri wrote:
>>>> Santosh,
>>>>
>>
>> ---Cut-------------------
>>
>>>>> I suspected the same. I know back then we started with SERDES code
>>>>> with NETCP but as you already know, its a separate block which
>>>>> is needed for NIC card to work. Its more of phy and hence its
>>>>> having different address space is not surprising.
>>>>
>>>> Using Phy interface is not acceptable to the subsystem maintainer based
>>>> on the communication I had on this. Also the Phy here is tighly coupled
>>>> with the hardware block it is working with. So this model is not right
>>>> for SerDes driver as it require additional enhancements as described
>>>> below if needs to be used.
>>>>
>>> Thanks for update on that.
>>>
>>>> The serdes initialization procedure requires checking the status in the
>>>> hardware block (PCIe, 1G or 10G) and then taking corrective action.
>>>> This
>>>> means a Phy driver would require mapping of related hw address space
>>>> (PCIe, 1G and 10G) as well which is already mapped by the hardware
>>>> driver(PCIe, 1G and 10G). One solution is to treat this as a libray
>>>> function that can be called from the respective hardware device driver.
>>>> A device node of h/w device (PCIe or 1G) in such as looks like
>>>>
>>> Or SerDes driver can embed the status reg address space.
>>> This is read only access so should be fine.
>>>
>>>> pcie {
>>>>
>>>> serdes@someaddress {
>>>> reg = <address of serdes>;
>>>> }
>>>> }
>>>>
>>>> hw driver will call ks2_serdes_init(node, hw_base_address) to
>>>> initialize
>>>> the serdes. Other APIs can be added to enable/disable lane or shutdown
>>>> etc. The libary will be added to drivers/soc/ti/ and used by various
>>>> device drivers to initialize and use the phy. As the serdes is slightly
>>>> integrated with the hardware block, IMO, this is a better approach than
>>>> using the phy model. The API definitions will be added to
>>>> include/linux/soc/ti/ folder.
>>>>
>>> Serdes Driver with its status register address space might solve this
>>> sharing problem. Library might work but we should try to have driver
>>> considering there is a physical device. I don't have strong opinion
>>> on drivers vs library.
>>>
>>
>> In addition to checking status in the SerDes, it needs to also check the
>> status of the associated hardware block (PCIe, 1G, 10G etc). So this
>> means, same needs to be mapped twice, first by the above hardware device
>> drivers and then by the serdes driver which causes problem. My point is
>> since they both are tightly coupled, a libary is a better option. That
>> way the mapped address can be passed to the serdes API to perform the
>> required task, instead of using Phy API which doesn't allow us to do the
>> same. If SerDes h/w can be brought up independently, the Phy model fits
>> well.
>>
> As I said, I don't have strong preference and fine with library approach.
> I suggest you do a RFC to take this further. Include Arnd on CC for
> that.

Sure!

Murali
>
> Regards,
> Santosh
>
>
>
>


--
Murali Karicheri
Linux Kernel, Keystone


\
 
 \ /
  Last update: 2015-09-02 21:01    [W:0.047 / U:0.668 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site