lkml.org 
[lkml]   [2015]   [Sep]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 20/27] ARM: dts: dra7: Fix NAND device nodes.
Date
Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.

The GPMC driver now implements gpiochip and irqchip so
enable gpio-controller and interrupt-controller properties.

With this the interrupt parent of NAND node changes so fix it
accordingly.

Signed-off-by: Roger Quadros <rogerq@ti.com>
---
arch/arm/boot/dts/dra7-evm.dts | 5 ++++-
arch/arm/boot/dts/dra7.dtsi | 4 ++++
arch/arm/boot/dts/dra72-evm.dts | 5 ++++-
3 files changed, 12 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts
index a6c82e5..8a31161 100644
--- a/arch/arm/boot/dts/dra7-evm.dts
+++ b/arch/arm/boot/dts/dra7-evm.dts
@@ -585,9 +585,12 @@
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&nand_flash_x16>;
- ranges = <0 0 0 0x01000000>; /* minimum GPMC partition = 16MB */
+ ranges = <0 0 0x08000000 0x01000000>; /* minimum GPMC partition = 16MB */
nand@0,0 {
+ compatible = "ti,omap2-nand";
reg = <0 0 4>; /* device IO registers */
+ interrupt-parent = <&crossbar_mpu>;
+ interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
ti,nand-ecc-opt = "bch8";
ti,elm-id = <&elm>;
nand-bus-width = <16>;
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index 5d65db9..f0a3616 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -1389,6 +1389,10 @@
gpmc,num-waitpins = <2>;
#address-cells = <2>;
#size-cells = <1>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
status = "disabled";
};

diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts
index 6f6bd98..245f5f9 100644
--- a/arch/arm/boot/dts/dra72-evm.dts
+++ b/arch/arm/boot/dts/dra72-evm.dts
@@ -395,13 +395,16 @@
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&nand_default>;
- ranges = <0 0 0 0x01000000>; /* minimum GPMC partition = 16MB */
+ ranges = <0 0 0x08000000 0x01000000>; /* minimum GPMC partition = 16MB */
nand@0,0 {
/* To use NAND, DIP switch SW5 must be set like so:
* SW5.1 (NAND_SELn) = ON (LOW)
* SW5.9 (GPMC_WPN) = OFF (HIGH)
*/
+ compatible = "ti,omap2-nand";
reg = <0 0 4>; /* device IO registers */
+ interrupt-parent = <&crossbar_mpu>;
+ interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
ti,nand-ecc-opt = "bch8";
ti,elm-id = <&elm>;
nand-bus-width = <16>;
--
2.1.4


\
 
 \ /
  Last update: 2015-09-18 17:21    [W:0.298 / U:1.808 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site