lkml.org 
[lkml]   [2015]   [Sep]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 10/27] mtd: nand: omap: Copy platform data parameters to omap_nand_info data
Date
Copy all the platform data parameters to the driver's local data
structure 'omap_nand_info' and use it in the entire driver. This will
make it easer for device tree migration.

Signed-off-by: Roger Quadros <rogerq@ti.com>
---
drivers/mtd/nand/omap2.c | 26 ++++++++++++++++++--------
1 file changed, 18 insertions(+), 8 deletions(-)

diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c
index 267bcdd..c35405c 100644
--- a/drivers/mtd/nand/omap2.c
+++ b/drivers/mtd/nand/omap2.c
@@ -152,14 +152,18 @@ static struct nand_hw_control omap_gpmc_controller = {
};

struct omap_nand_info {
- struct omap_nand_platform_data *pdata;
struct mtd_info mtd;
struct nand_chip nand;
struct platform_device *pdev;

int gpmc_cs;
- unsigned long phys_base;
+ bool dev_ready;
+ enum nand_io xfer_type;
+ int devsize;
enum omap_ecc ecc_opt;
+ struct device_node *elm_of_node;
+
+ unsigned long phys_base;
struct completion comp;
struct dma_chan *dma;
int gpmc_irq;
@@ -1656,7 +1660,7 @@ static bool omap2_nand_ecc_check(struct omap_nand_info *info,
"CONFIG_MTD_NAND_OMAP_BCH not enabled\n");
return false;
}
- if (ecc_needs_elm && !is_elm_present(info, pdata->elm_of_node)) {
+ if (ecc_needs_elm && !is_elm_present(info, info->elm_of_node)) {
dev_err(&info->pdev->dev, "ELM not available\n");
return false;
}
@@ -1701,6 +1705,11 @@ static int omap_nand_probe(struct platform_device *pdev)
info->gpmc_cs = pdata->cs;
info->of_node = pdata->of_node;
info->ecc_opt = pdata->ecc_opt;
+ info->dev_ready = pdata->dev_ready;
+ info->xfer_type = pdata->xfer_type;
+ info->devsize = pdata->devsize;
+ info->elm_of_node = pdata->elm_of_node;
+
mtd = &info->mtd;
mtd->priv = &info->nand;
mtd->name = dev_name(&pdev->dev);
@@ -1727,7 +1736,7 @@ static int omap_nand_probe(struct platform_device *pdev)
* chip delay which is slightly more than tR (AC Timing) of the NAND
* device and read status register until you get a failure or success
*/
- if (pdata->dev_ready) {
+ if (info->dev_ready) {
nand_chip->dev_ready = omap_dev_ready;
nand_chip->chip_delay = 0;
} else {
@@ -1741,15 +1750,16 @@ static int omap_nand_probe(struct platform_device *pdev)
nand_chip->options |= NAND_SKIP_BBTSCAN;

/* scan NAND device connected to chip controller */
- nand_chip->options |= pdata->devsize & NAND_BUSWIDTH_16;
+ nand_chip->options |= info->devsize & NAND_BUSWIDTH_16;
if (nand_scan_ident(mtd, 1, NULL)) {
- dev_err(&info->pdev->dev, "scan failed, may be bus-width mismatch\n");
+ dev_err(&info->pdev->dev,
+ "scan failed, may be bus-width mismatch\n");
err = -ENXIO;
goto return_error;
}

/* re-populate low-level callbacks based on xfer modes */
- switch (pdata->xfer_type) {
+ switch (info->xfer_type) {
case NAND_OMAP_PREFETCH_POLLED:
nand_chip->read_buf = omap_read_buf_pref;
nand_chip->write_buf = omap_write_buf_pref;
@@ -1812,7 +1822,7 @@ static int omap_nand_probe(struct platform_device *pdev)

default:
dev_err(&pdev->dev,
- "xfer_type(%d) not supported!\n", pdata->xfer_type);
+ "xfer_type(%d) not supported!\n", info->xfer_type);
err = -EINVAL;
goto return_error;
}
--
2.1.4


\
 
 \ /
  Last update: 2015-09-18 17:21    [W:2.210 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site