lkml.org 
[lkml]   [2015]   [Sep]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [Bugfix 0/3] Convert eata driver to a normal PCI device driver


Jiang Liu wrote on 14/09/15 12:38:
> Hi Authur,
> As suggested by Bjorn, patch 1-2 set implement a PCI device
> driver to manage eata PCI devices. And patch 3 tries to support PCI
> device hot-removal for eata, but I have no change to test due to
> limited knowledge about scsi subsystem and lacking of hardware for
> tests.
> So you could please help to test patch 1-2? Patch 3 is just
> for comments.
> Thanks!
> Gerry
>
> Jiang Liu (3):
> eata: Use IDA to manage eata board IDs
> eata: Implement PCI driver to manage eata PCI devices
> eata: Enhance eata driver to support PCI device hot-removal
>
> drivers/scsi/eata.c | 232 +++++++++++++++++++++++++++------------------------
> 1 file changed, 125 insertions(+), 107 deletions(-)
>

With patches 1 and 2 applied, I get a successful boot with IRQ mapping:

[ 1.147056] EATA0: IRQ 10 mapped to IO-APIC IRQ 17.
[ 1.160404] EATA/DMA 2.0x: Copyright (C) 1994-2003 Dario Ballabio.
[ 1.160469] EATA config options -> tm:1, lc:y, mq:16, rs:y, et:n,
ip:n, ep:n, pp:y.
[ 1.160541] EATA0: 2.0C, PCI 0xd890, IRQ 17, BMST, SG 122, MB 64.
[ 1.160600] EATA0: wide SCSI support enabled, max_id 16, max_lun 8.
[ 1.160658] EATA0: SCSI channel 0 enabled, host target ID 7.
[ 1.161207] scsi host0: EATA/DMA 2.0x rev. 8.10.00


but I still get errors when trying to do a kexec reboot, see
http://www.users.on.net/~arthur.marsh/20150915547.jpg

roughly it reads (after the synchronising SCSI cache reboot messages)
and a long period of a dark screen:

sd 0:0:6:0: abort, mbox 63.
EATA0: abort, mbox 63 is in use.
sd 0:0:6:0: reset, enter.
EATA0: reset, mbox 63 in reset.
EATA0: reset, board reset done, enabling interrupts.
EATA0: reset, interrupts disabled, loops 100469.
EATA0: reset, mbox 63 locked, DID_RESET, done.
EATA0: reset, exit, done.
sd 0:0:6:0: qcomm, mbox 0, adapter busy, will start
sd 0:0:6:0: abort, mbox 0.
EATA0: abort, timeout error.
sd 0:0:6:0: reset, enter.
EATA0: reset, exit, timeout error.
sd 0:0:6:0 Device offlinled - not ready after error recovery
sd 0:0:6:0 rejecting I/O to offline device
sd 0:0:6:0 rejecting I/O to offline device
sd 0:0:6:0 [sda] Synchronize Cache(10) failed: Result:
hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
starting new kernel

It would be great if this problem could be fixed.

Arthur.



\
 
 \ /
  Last update: 2015-09-14 18:21    [W:1.377 / U:0.004 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site