lkml.org 
[lkml]   [2015]   [Sep]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH-v5 RESEND 3/5] i2c: pxa: Add support for pxa910/988 & new configuration features
From
Date


On Saturday 12 September 2015 12:36 AM, Wolfram Sang wrote:
> On Mon, Aug 24, 2015 at 11:29:36AM +0530, Vaibhav Hiremath wrote:
>> TWSI_ILCR & TWSI_IWCR registers are used to adjust clock rate
>> of standard & fast mode in pxa910/988; so this patch adds these two new
>> entries to "struct pxa_reg_layout" and "struct pxa_i2c".
>>
>> As discussed in the previous patch-series, the idea here is to add standard
>> DT properties for ilcr and iwcr configuration fields.
>> In case of Master ilcr is used for low/high time and in case of slave mode
>> of operation iwcr is used for setup/hold time.
>
> I need to rethink how to describe i2c bus timing parameters in DT in the
> next days. But this is planned for 4.4., promised.
>
> One thing I already wonder about this one...
>
>> static const struct platform_device_id i2c_pxa_id_table[] = {
>> { "pxa2xx-i2c", REGS_PXA2XX },
>> { "pxa3xx-pwri2c", REGS_PXA3XX },
>> { "ce4100-i2c", REGS_CE4100 },
>> + { "pxa910-i2c", REGS_PXA910 },
>> { },
>
> You add a new platform_id...
>
>> @@ -1135,7 +1170,7 @@ static const struct i2c_algorithm i2c_pxa_pio_algorithm = {
>> static const struct of_device_id i2c_pxa_dt_ids[] = {
>> { .compatible = "mrvl,pxa-i2c", .data = (void *)REGS_PXA2XX },
>> { .compatible = "mrvl,pwri2c", .data = (void *)REGS_PXA3XX },
>> - { .compatible = "mrvl,mmp-twsi", .data = (void *)REGS_PXA2XX },
>> + { .compatible = "mrvl,mmp-twsi", .data = (void *)REGS_PXA910 },
>> {}
>
> ...but change the compatible binding instead of adding a new one?
>

Yes, because the offset for both REGS_PXA2XX and REGS_PXA910 are same,
and for REGS_PXA2XX we already have compatible entry "mrvl,pxa-i2c".
And the i2c binding documentation, which says,
for platforms using REGS_PXA2XX, they need to provide additional node
"mrvl,pxa-i2c". Which is confusing :)

Also, when I did git-blame on the driver file to see why "mmp-twsi"
entry has been added without anyone really using it. But I did not find
anything meaningful.
So, from the code it was very clear that, "mmp-twsi" and "pxa-i2c" both
are same, its the code which I am adding here brings difference between
them.

I tried to find datasheet for the platforms using "mmp-twsi", but was
unlucky.


Thanks,
Vaibhav




Thanks,
Vaibhav


\
 
 \ /
  Last update: 2015-09-14 07:41    [W:0.079 / U:0.748 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site