lkml.org 
[lkml]   [2015]   [Jul]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v3 00/11] USB: OTG/DRD Core functionality
From
Hi Roger,

On Wed, Jul 15, 2015 at 6:26 AM, Roger Quadros <rogerq@ti.com> wrote:
> Hi Andrew,
>
> On 13/07/15 22:14, Andrew Bresticker wrote:
>> Hi Roger,
>>
>> On Wed, Jul 8, 2015 at 3:19 AM, Roger Quadros <rogerq@ti.com> wrote:
>>> Usage model:
>>> -----------
>>>
>>> - The OTG controller device is assumed to be the parent of
>>> the host and gadget controller. It must call usb_otg_register()
>>> before populating the host and gadget devices so that the OTG
>>> core is aware that it is an OTG device before the host & gadget
>>> register. The OTG controller must provide struct otg_fsm_ops *
>>> which will be called by the OTG core depending on OTG bus state.
>>
>> I'm wondering if the requirement that the OTG controller be the parent
>> of the USB host/device-controllers makes sense. For some context, I'm
>> working on adding dual-role support for Tegra210, specifically on a
>> system with USB Type-C. On Tegra, the USB host-controller and USB
>> device-controller are two separate IP blocks (XUSB host and XUSB
>> device) with another, separate, IP block (XUSB padctl) for the USB PHY
>> and OTG support. In the non-Type-C case, your OTG framework could
>> work well, though it's debatable as to whether or not the XUSB padctl
>> device should be a parent to the XUSB host/device-controller devices
>> (currently it isn't - it's just a PHY provider). But in the Type-C
>> case, it's an off-chip embedded controller that determines the
>> dual-role status of the Type-C port, so the above requirement doesn't
>> make sense at all.
>>
>> My idea was to have the OTG/DRD controller explicitly specify its host
>> and device controllers, so in DT, something like:
>>
>> otg-controller {
>> ...
>> device-controller = <&usb_device>;
>> host-controller = <&usb_host>;
>> ...
>> };
>>
>> usb_device: usb-device@.... {
>> ...
>> };
>>
>> usb_host: usb-host@... {
>> ...
>> };
>>
>> What do you think?
>
> I agree that we need to support your use case but how to do it
> is not yet clear to me.
>
> In your above example the otg controller knows what are the host
> and gadget controllers but the host/gadget devices don't
> know who is their otg controller.
>
> So the problem is that when usb_otg_register_hcd/gadget() is called
> we need to get a handle to the otg controller.
>
> One solution I see is to iterate over the registered otg_controller_list
> and check if we match the host/gadget controller in there.
>
> Then there is also a possibility that host/gadget controllers get
> registered before the OTG controller. Then we can't know for sure if
> the host/gadget controller was meant for dual-role operation or not
> and it will resort to single role operation.
>
> Any idea to prevent the above situation?
>
> Maybe we need to add some logic in host/gadget cores to check if the port
> is meant for dual-role use and defer probe if OTG controller is not yet
> registered?

In the DT case, I think we could add an "otg-controller" property to
the host and gadget nodes, and in usb_otg_register_{hcd,gadget}()
check for that property and defer probe if the referenced OTG
controller has not yet been registered. Not sure how to indicate that
a host/gadget is meant for dual-role operation on non-DT platforms
though.

Thanks,
Andrew


\
 
 \ /
  Last update: 2015-07-16 20:41    [W:0.232 / U:0.076 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site