lkml.org 
[lkml]   [2015]   [Dec]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH v9 3/3] MIPS: dts: jz4780/ci20: Add NEMC, BCH and NAND device tree nodes
On Thu, 3 Dec 2015 12:02:22 +0000
Harvey Hunt <harvey.hunt@imgtec.com> wrote:

> From: Alex Smith <alex.smith@imgtec.com>
>
> Add device tree nodes for the NEMC and BCH to the JZ4780 device tree,
> and make use of them in the Ci20 device tree to add a node for the
> board's NAND.
>
> Note that since the pinctrl driver is not yet upstream, this includes
> neither pin configuration nor busy/write-protect GPIO pins for the
> NAND. Use of the NAND relies on the boot loader to have left the pins
> configured in a usable state, which should be the case when booted
> from the NAND.
>
> Signed-off-by: Alex Smith <alex.smith@imgtec.com>
> Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
> Cc: David Woodhouse <dwmw2@infradead.org>
> Cc: Brian Norris <computersforpeace@gmail.com>
> Cc: Paul Burton <paul.burton@imgtec.com>
> Cc: linux-mtd@lists.infradead.org
> Cc: devicetree@vger.kernel.org
> Cc: linux-kernel@vger.kernel.org
> Cc: linux-mips@linux-mips.org
> Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
> ---
> v8 -> v9:
> - Represent the partition table as a subnode of a NAND chip.
>
> v7 -> v8:
> - Describe the NAND chips as children nodes of the NAND controller.
> - Remove ingenic, prefix from ECC settings.
> - Renamed some ECC settings.
>
> v6 -> v7:
> - Add nand-ecc-mode to DT.
> - Add nand-on-flash-bbt to DT.
>
> v4 -> v5:
> - New patch adding DT nodes for the NAND so that the driver can be
> tested.
>
> arch/mips/boot/dts/ingenic/ci20.dts | 63 ++++++++++++++++++++++++++++++++++
> arch/mips/boot/dts/ingenic/jz4780.dtsi | 26 ++++++++++++++
> 2 files changed, 89 insertions(+)
>
> diff --git a/arch/mips/boot/dts/ingenic/ci20.dts b/arch/mips/boot/dts/ingenic/ci20.dts
> index 9fcb9e7..782258c 100644
> --- a/arch/mips/boot/dts/ingenic/ci20.dts
> +++ b/arch/mips/boot/dts/ingenic/ci20.dts
> @@ -42,3 +42,66 @@
> &uart4 {
> status = "okay";
> };
> +
> +&nemc {
> + status = "okay";
> +
> + nandc: nand-controller@1 {
> + compatible = "ingenic,jz4780-nand";
> + reg = <1 0 0x1000000>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ingenic,bch-controller = <&bch>;
> +
> + ingenic,nemc-tAS = <10>;
> + ingenic,nemc-tAH = <5>;
> + ingenic,nemc-tBP = <10>;
> + ingenic,nemc-tAW = <15>;
> + ingenic,nemc-tSTRV = <100>;

I guess those are encoding controller specific timings. Maybe they
could be automatically deduced from nand_timings information (I'm not
asking to implement that right now, but keep it in the back of your
mind as possible future improvements).


--
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

\
 
 \ /
  Last update: 2015-12-08 15:41    [W:0.432 / U:0.372 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site