lkml.org 
[lkml]   [2015]   [Dec]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v1 04/10] serial: mps2-uart: add MPS2 UART driver
From
On Tue, Dec 15, 2015 at 2:40 PM, Vladimir Murzin
<vladimir.murzin@arm.com> wrote:
> On 12/12/15 23:39, Andy Shevchenko wrote:
>> On Wed, Dec 2, 2015 at 11:33 AM, Vladimir Murzin
>> <vladimir.murzin@arm.com> wrote:
>>> This driver adds support to the UART controller found on ARM MPS2
>>> platform.
>>
>> Just few comments (have neither time not big desire to do full review).
>>
>
> Still better than nothing ;) I'm mostly agree on points you had, so I've
> just left some I'm doubt about...
>
>>> +
>>> +static void mps2_uart_enable_ms(struct uart_port *port)
>>> +{
>>> +}
>>> +
>>> +static void mps2_uart_break_ctl(struct uart_port *port, int ctl)
>>> +{
>>> +}
>>
>> Are those required to be present? If not, remove them until you have
>> alive code there.
>
> A quick grep shows that core calls mps2_uart_break_ctl()
> unconditionally, but, yes, it checks for presence of
> mps2_uart_enable_ms() before jumping there, so it is safe to remove latter.

OK.

>>> +static irqreturn_t mps2_uart_oerrirq(int irq, void *data)
>>> +{
>>> + irqreturn_t handled = IRQ_NONE;
>>> + struct uart_port *port = data;
>>> + u8 irqflag = mps2_uart_read8(port, UARTn_INT);
>>> +
>>> + spin_lock(&port->lock);
>>> +
>>> + if (irqflag & UARTn_INT_RX_OVERRUN) {
>>> + struct tty_port *tport = &port->state->port;
>>> +
>>> + mps2_uart_write8(port, UARTn_INT_RX_OVERRUN, UARTn_INT);
>>> + tty_insert_flip_char(tport, 0, TTY_OVERRUN);
>>> + port->icount.overrun++;
>>> + handled = IRQ_HANDLED;
>>> + }
>>> +
>>> + /* XXX: this shouldn't happen? */
>>
>> If shouldn't why it's there? Otherwise better to explain which
>> conditions may lead to this.
>>
>
> In practice I've never seen that happened and I think it never *should*
> happen since we check if there is room in TX buffer. However, I could be
> wrong here, so it is why that statement has question mark.

So, worth to have a proper comment then.

>>> +static int __init mps2_uart_init(void)
>>> +{
>>> + int ret;
>>> +
>>> + ret = uart_register_driver(&mps2_uart_driver);
>>> + if (ret)
>>> + return ret;
>>> +
>>> + ret = platform_driver_register(&mps2_serial_driver);
>>> + if (ret)
>>> + uart_unregister_driver(&mps2_uart_driver);
>>> +
>>> + pr_info("MPS2 UART driver initialized\n");
>>> +
>>> + return ret;
>>> +}
>>> +module_init(mps2_uart_init);
>>> +
>>> +static void __exit mps2_uart_exit(void)
>>> +{
>>> + platform_driver_unregister(&mps2_serial_driver);
>>> + uart_unregister_driver(&mps2_uart_driver);
>>> +}
>>> +module_exit(mps2_uart_exit);
>>
>> module_platform_driver();
>> And move uart_*register calls to probe/remove.
>>
>
> With this move we'll get uart_*register for every device probed, no?

Don't see a problem, maybe someone else could share an authoritive opinion.
Some of the drivers do that, though most do in __init stage. So, see above.

--
With Best Regards,
Andy Shevchenko


\
 
 \ /
  Last update: 2015-12-17 14:41    [W:0.060 / U:0.564 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site